您要查找的是不是:
- The results show that the density is the most notable factor,and hot pressing temperature and dose of bagasse are secondary. 试验结果表明:速生杨木/甘蔗渣重组材的密度是最显著性的影响因素,其次为热压温度和甘蔗渣加量。
- The factors are hot pressing temperature, glue spread, BL-formaldehyde absorptive reagent spread and hot pressing time in influence sequence. 影响大小次序是热压温度>脲胶施加量>BL-甲醛消纳剂施加量>热压时间。
- Temperature distribution was tested along thickness direction of Dendrocalamus giganteus timber under different hot pressing temperatures. 测定了龙竹竹材在不同热压温度下干燥时的温度分布。
- 4.Formaldehyde emission becomes lower with increase of BL- formaldehyde absorptive reagent spread, augment of hot pressing temperature, prolongation of hot pressing time. 4.;单因素试验时,随着BL-甲醛消纳剂施加量的增加、热压温度的升高、热压时间的延长,甲醛释放量越低;
- hot pressing temperature 热压温度
- hot press temperature 热压温度
- Compressing moulding presses.., hot press... 就是液压机什么得。。。
- A new type BN ceramic material is made by hot pressing(HP) method. 采用热压(HP)法制备了BN陶瓷材料。
- By using the system, pressing time could be automatically changed with the temperature of hot press platen. 这个系统能随着热压板温度的变化自动调整保压时间。
- Accurate, safety, and steady controlled temperature of PVC heater and hot-sealing roll heater (hot pressing roller) without harm to packing material and drugs. 控制加热器和热压板加热器的温度控制准确,安全可靠,不会对包装材料和药品造成损伤。(铝塑铝设备)
- The effect of hot pressing sintering temperature,pressure and time on its properties are investigated by means of orthogonality rejection and variance analysis. 采用正交设计和方差分析的方法研究了热压烧结温度、压力、时间对该砂轮性能的影响。
- The powder can be directly consolidated into blocks via hot pressing. 这些粉末可以通过热压形成整块。
- TiB2-Si3N4-BN composite was fabricated by hot press , and the influence of the content of additive and sintering temperature on the property is also discussed. 采用真空热压烧结方法制备了TiB2-BN复合材料,探讨了Si3N4掺加剂含量和烧结温度对材料结构和性能的影响。
- The effect of ambient temperature on the friction and wear properties of poly(m phenylene isophalamide)(PMIA) prepared by hot pressing method were studied using a pin on disc wear tester. 用栓盘式端面摩擦磨损试验机在干摩擦条件下考察了环境温度对热压成型的聚间苯二甲酰间苯二胺(PMIA)摩擦磨损性能的影响。
- At the polyalkene Oct.1999, after the injection molding, hot press as molding. 一般以聚烯烃为主要原材料,经过注塑、热压等工艺加工成型。
- Two hot pressing shaped, Ms. Man face, schoolbags sandwich, mainly Middle Eastern countries and regions. 两次热压成型、奥古曼面、意杨夹心、主要针对中东国家和地区。
- The polycrystalline Na-Bata-Al_2O_3 with relative density greater than 99% has been prepared by means of hot pressing. 用热压的方法可制得相对密度大于99%25的Na-Beta-Al_2O_3。
- Ti2AlC bulk material was synthesized by hot pressing using elemental powder mixture of Ti,Al and active carbon. 以Ti、Al元素粉和活性炭为原料,采用热压工艺合成了Ti2AlC块体材料。
- TiB2-Al2O3 Multiphase ceramics with Y2O3-La2O3 as sintering aids are fabricated by hot pressing. 本文以Y2O3-La2O3为烧结助剂,通过热压烧结制备了TiB2-Al2O3复相陶瓷,研究了原料组成对材料的显微结构和力学性能的影响。
- The monoclinic celsian phase in the matrix was produced in situ,during hot pressing,from amphosous BAS. 在热压期间,基体中的单斜相钡长石由玻璃态钡长石原位转变生成。