您要查找的是不是：
- He is pitching hay onto the high load. 他正在把干草抛到高高的草堆上。
- With PP chips and antibacterial matrices blent,the antibacterial special raw material with high melt index is prepared for speed spinning. 采用聚丙烯切片、抗菌母粒共混,制成高熔融指数的抗菌高速纺专用料进行纺丝。
- By blending Plastic grade PP chips and far-infrared matrices, the far-infrared special raw material with high melt index was prepared for high speed spinning. 采用塑料级聚丙烯切片与远红外母粒共混改性造粒,制咸高熔融指数的远红外高速纺专用料进行纺丝。
- A torsion bar is used in a high load capacity truck. 扭力杆用于高承载量的卡车。
- Heating zone with low thermal inertia to allow high load variations. 加温区带有低温惯性装置允许高温下负载变化。
- The melt index (MI) ofpolypropylene (PP) has significant effects on the impregnation and interface forming process in GMT making. 聚丙烯的熔融指数对GMT的浸渍过程及界面形成过程有着重要的影响。
- The application results on real industrial process show that AKPLS can predict the polypropylene melt index more accurately than PLS and KPLS. 工业数据应用结果表明，所提出的AKPLS方法能够比PLS、KPLS方法更准确地预报聚丙烯熔融指数的变化。
- A tire with a higher load index than that of the Original Equipment tire indicates an increase in load capacity. 轮胎负载指数较高于原设备轮胎表明增加负荷能力。
- Run that with a high load setting and ensure that your server stays up until the load test finishes. 以一个高的负载设置运行那个工具以确信你的服务器能够承受直到测试结束。
- Influence of inorganic pigments on toner morpology and relations of toner composition with glass transition temperature,soften temperature and melt index were investigated. 考察了无机颜料对墨粉颗粒形貌的影响； 墨粉的玻璃化转变温度、软化点、熔融指数与墨粉组成的关系；
- The influences of substrates, melt index (MI) and VAC content in EVA, selection and add-on of peeling force stabilizers on the properties of projective f ilm products are studied. 研究了基材、EVA中熔融指数和醋酸乙烯含最、剥离力稳定剂的选择及用量对保护膜产品性能的影响。
- The development of high power supply is to use the paralleled power supply modules to meet requirement of high load. 摘要大功率电源系统的发展趋势是实现电源组件模块化，再通过多个模块的并联以满足负载功率的要求。
- JDB JFB HAVE LOWER FRICTION,HIGHER LOAD AND LONG LIFE. JDB具有低的摩擦系数，高承载的能力及使用寿命长优点。
- The effects of various parameters, such as monomer (MAH) , initiator(DCP) concentration and process condition on grafting percentage and melt index (MFR) wen-studied . 考察了单体、引发剂用量和加工条件对接枝率及熔体流动速率的影响。
- The mechanism shows hysteresis friction at low load while adhesive friction at high load. 在较低载荷时,丁腈橡胶表现为滞后摩擦,在较高载荷时,表现为粘着摩擦;
- The graffing rate and melt index of MAH g PE are investigated.It shows that CALA could decrease crosslinkage degree of the copolymer and improve the flowing property of the melt. 结果表明:合成过程中少量己内酰胺的加入,在不明显降低接枝物接枝率的情况下可以明显改善接枝物的熔体粘度,提高了接枝物的流动性能。
- Effects of two components' melt index, spinning temperature, lateral blowing, drawing ratio, crimping and heat setting on fiber quality and properties are discussed. 讨论了两种切片的熔融指数、纺丝温度、侧吹风、后拉伸倍数、卷曲、松弛定型工艺对产品质量及性能的影响。
- A constant 1.2 MHz switching frequency, with current-mode control scheme, provides stable low-noise operation at high load conditions. 恒定的1.;2 MHz开关频率及电流模式控制配置可确保高载荷条件下稳定的低噪音操作。
- The contactless measuring method based on the Hall effect combines excellent switching accuracy with high stability, even under high load alternations. 基于霍尔效应的无触点测量方法结合了极高的开关精度和即使在高负载变化下也具有的高稳定性。
- Needle roller bearings with rings of carbon chromium (bearing) steel have low sectional height and very high load carrying capacity for their size. 带有碳铬(轴承)钢圈的滚针轴承与其尺寸相对的截面高度低、载荷能力很高。
