您要查找的是不是：
- The second crack is a crack originating at the groove weld toe of the column flange-girder flange connection. 第二种是产生于立柱翼缘与主梁翼缘连接处的坡口焊缝焊趾处的裂纹。
- These attachments were considered secondary components, so no weld quality control has been imposed on the groove weld splice. 这些附连件被看作是次要的部件，所以在这种坡口焊接中没有进行焊接质量控制。
- The effective weld length for any groove weld, perpendicular or skewed to the direction of stress, shall be the width of the part joined. 对于任何开槽焊接，有效的焊接长度就是零件结合的宽度，且要垂直或倾斜于压力方向。
- This paper describes the difference between the terms of groove and bevel in weld joints and condition in ASME Code translation. 本文叙述焊接接头中术语剖口与坡口的区别和在ASME规范翻译中应注意的问题。
- Microporosity in thermite weld joint consiste of blow hole and shrinkage cavities. 氧或硅含量过高形成氧化物或硅酸盐;
- Mainly used in coating the weld joint of buried steel pipeline and insulated pipeline. 主要用于埋地钢质管道现场焊接补口和保温管线现场补口；
- The corrosion behavior of austenite stainless steel weld joint in the different acidic medium was studied. 研究了奥氏体不锈钢焊接接头在不同酸性介质中的腐蚀行为。
- Using the modulated laser beam to weld plastics simultaneously, the figure of ideal weld joint was identical with the desired one. 利用调制完成后的激光束对塑料进行同步焊接，得到理想焊缝与预知焊缝形状相同的结果。
- The distribution of residual stress of weld joints is analyzed. 并分析了焊接接头残余应力的分布规律。
- Often lack of fusion adjacent to the girder web in the transverse groove welds led to the cracking. 在靠近主梁腹板的横向坡口焊缝处常常出现未熔透而导致裂纹。
- Cracks have been found in the flange and web splices at groove welds in at least four bridges. 至少在四座桥梁的翼缘板和腹板拼接坡口焊缝中发现了裂纹。
- Weldbonding experiments were performed and the results show that weldbonding technique can improve the strength and fatigue life of the weld joint. 同时参考分析结果进行粘接点焊的试验研究，表明粘接点焊可以显著提高结构的强度和疲劳寿命。
- A large number of these cracks occurred because the groove welded component was considered a secondary member or attachment. 发生这许多裂纹是因为把这些坡口焊接部件作为次要构件或附件考虑。
- Seals underbody, weld joints, trunk interior and firewall of motor vehicles. 汽车底盘，焊缝，卡车内饰等。
- In this article, based on the failure type and failure mechanism of the monel alloy weld joint, the weldability of the material was analyzed, and the weld joint type and weld material were, then, determined. 本文就蒙乃尔合金焊接接头的失效方式、失效机理 ,分析了材料的可焊性 ,并确定其焊材和焊接接头结构型式。
- The paper discussed the fact that the content of sulphur and chlorine in the penetrant will accelerates the crack producing and expending in Austenite weld joint of Chrome-Nickel steel. 讨论渗透剂中硫和氯的含量促使铬镍奥氏体焊缝中裂纹的产生和发展。
- Complete joint penetration groove weld(statically and dynamically loaded structures) 接头全焊透坡口焊缝(静载或动载结构)
- The paper introduces single "U" groove welding procedure for stainless steel inner cylinder of multilayer high pressure vessel,opening up a new method for welding clading stainless steel vessel. 要详细介绍了内商为不锈钢的多层高压容器外U形坡口的单面焊接工艺，从而为不锈钢复合容器的焊接开辟了一条新途径。
- And by communicating between the PC and microchip controller, it can realize to real-time monitor microchip controller, so that the system can forecast and control the weld joint properties. 并通过上下位机之间的数据通信，对下位机进行实时监控，实现接头质量的预测与控制。
- The paper introduces single "U" groove welding procedure for stainless steel inner cylinder of multilayer high pressure vessel, opening up a new method for welding clading stainless steel vessel. 详细介绍了内筒为不锈钢的多层高压容器外U形坡口的单面焊接工艺，从而为不锈钢复合容器的焊接开辟了一条新途径。
