您要查找的是不是:
- The medium chromium white cast iron has been pouring by green sand mold, and the effect of Cr? Si? Mn? 应用湿砂铸型浇注中低铬白口铸铁 ,采用正交试验研究Cr、Si、Mn、Cu对铸态中低铬白口铸铁力学性能的影响。
- Coating of sodium silicate alumina caly for aluminium alloy casting in green sand mold is studied. 试验研究了应用于湿砂型铝合金铸件的以水玻璃为基、铝钒土为耐火填料的徐料。
- The mold hardness under different vacuum degree was tested.The results showed that the mold hardness of EPC process was higher than that of green sand mold and was more uniformly distributed. 不同真空度下消失模铸型硬度的测试结果表明,消失模铸型的硬度高于普通湿型砂铸型,并且硬度分布更均匀。
- Green Sand Mold Casting of Lengthy Casting 细长件的湿型铸造
- air permeability of clay green sand mold 型砂透气性
- Interior surfaces in green sand molds usually require more draft than exterior surfaces. 砂模的内表面经外表面需要更大的拔模斜度
- This paper outlines the basic principles,processes and equipments commonly used in V-process,green sand and resin sand moldings. 文章介绍了目前常用的真空V法造型、湿砂造型和树脂砂造型的基本原理、工艺过程以及所使用的设备,列举了它们的优缺点和经济的适用范围。
- Industrial Test of Groove Linear Board of Green Sand Mold Ball Grinding Machine 湿型球磨机槽型衬板工业性试验
- The Application of New Alcohol Based Spraying Coatings for Green Sand Mold 新型醇基喷涂涂料在粘土湿型砂中的应用
- A frame for holding a sand mold in a foundry. 砂箱铸造车间内保持砂模用的框架
- The Formation and Control of Imperfections of Small Castings of Green Sand Mold 铸造湿型小件缺陷产生的原因与控制
- The Prevention of Lift Core Defects of Green Sand Mold Steel Casting 湿型铸钢件偏芯缺陷的防止
- Test and Application of Green Sand Mold Coating in thin-plate Iron castings 薄壁铸铁件湿型铸造涂料的实验与应用
- Test and Application of Green Sand Molding Coating 潮型铸造涂料的实验与应用
- Moulding machines with green sand. 要有机械潮模砂造型。
- Progress of Research on Numerical Simulation of Green Sand Molding Process 湿型砂造型和制芯过程数值模拟研究进展
- green sand mold 湿砂型
- Abstract: One method to make casting sand mold directly from the bozzetto(mud-draft) of the sculpture is introduced. 文摘:介绍一种在雕塑泥稿外直接制作铸造砂型的方法。
- One method to make casting sand mold directly from the bozzetto(mud-draft) of the sculpture is introduced. 介绍一种在雕塑泥稿外直接制作铸造砂型的方法。
- EPC has larger resistance than that of sand mold casting in pouring process, and need double pouring time. 在相同浇注条件下,实型铸造的充型阻力较砂型铸造的大,浇注时间增加约一倍;