您要查找的是不是：
- glost warpage 翘曲, 弯曲; 畸变
- Surface smoothness and low warpage. 表面平滑,低翘曲性。
- The reported Warpage values may be lower than actual due to voiding. /纪录的弯曲度数值可能比实际应用的低。
- Adjusting delay time and gas pressure can reduce the warpage of the part. 工艺上可以通过调整延迟时间和气体压力来减小产品的变形量。
- Fin ger effect of gas is an important factor that can lead to warpage. 气体手指效应也是造成产品变形的一个重要因素;
- Moreover,fast filling and less time for holding were also dedicated to reduce the warpage of product... 适当提高注射速率和减少保压时间也可减小制品翘曲。
- The resulting benefits are high stiffness and load bearing at low weights and with low warpage. 最终带给产品的好处是在低重量和低翘曲情况下体现出的高刚性和承载能力。
- The lead frame with the opening in die pad can significantly improve the package warpage and die stresses. 导线架晶片座开槽型式，对构装翘曲及晶片应力也有明显改善效果。
- Study the warpage of the product and put compensate on mould to defeat the warpage. 学习研究陶瓷件的变形，并把预变形的补偿计算到模具里面。
- Using Moldflow software to make CAE simulation of the shrinkage and warpage of the product. 依据采集的模拟数据进行分析,得出注射模的型腔尺寸补偿方案,用于指导型腔尺寸的修整。
- The step to analyze warpage deformation by CAE is given with air condition damper vane as example. 用有限元方法研究了温度场、压力场对注塑件残余应力及翘曲变形的影响。
- Thermo-mechanical design is equally important when addressing complex substrates, warpage issues, and thermo-mechanical modeling. 热机械设计同样重要的是，在处理复杂的基板，翘曲的问题，和热机械模型。
- "Jinbiao" CMC be used as flowing control matter in ceramics glost substitute,which has the performance of retain glost substitute, to prevent it from getting to tear cicatrice before cooking finish. “金标”CMC在陶瓷釉料中加入作为一种流动控制剂，它具有持留釉料的性能，以防止釉料在烧成之前脱落成泪痕。
- Summary：The theory of the Newton ring method is analyzed and the chip warpage is measured by use of the Newton ring method. 摘要：分析了牛顿环法的测量原理，利用牛顿环法对芯片翘曲度进行了测量。
- All these can be well used for reference to study the cause of molding defects (e. g. warpage, weld line) of ultra-thin wall plastic parts thoroughly. 该结论为深入开展超薄塑件成型缺陷（如翘曲、熔接痕）的形成机理研究提供了有益的借鉴。
- The results showed that the warpage decreased with the decrease of mold temperature,nozzle temperature and hold preasure. 结果表明,随着模具温度、喷嘴温度和保压压力的降低,制品的翘曲减小;
- A predictive model for warpage is created using feed forward artificial neural network exploiting finite element analysis results. 建立了使用有限元分析结果的具有提前输入（功能）的人造神经网络的扭曲预制模型。
- A numerical study of residual stresses and warpage was undertaken according to the characteristics of plastic injection molding process. 针对塑料注射成型工艺的特点,提出了残余应力和翘曲变形的数值模拟方法。
- WIT's ability to pack out a part consistently can reduce sinks and warpage while lessening the degree of mold texturing required. 水辅注射能够在不苛责模具型腔表面质地的前提下稳定保压消除塌陷和翘曲。
- Features Good thermal reliability and moisture resistance, lower warpage, good mechanical properties and electrical properties. 特性 良好的耐热性、耐湿性、平整性，良好的机械性能和电性能。
