您要查找的是不是：
- Study on Geometrical Tolerance of Mould Manufacture 模具制造中形位误差剖析及对策探讨
- indication of geometrical tolerance 形位公差标注
- RECIPROCITY REQUIREMENT AND ZERO GEOMETRICAL TOLERANCE 可逆要求与零形位公差
- Taking into account assembly tolerance and geometric tolerance, with the maximum and minimum method, a parallel degree calculating method for the missile launcher is put forward. 以某型空空导弹四联装发射装置为例,对空间尺寸链的设计计算方法进行了研究。
- General dimensional tolerance and geometric tolerance stipulated in this standard are applicable to weldment, welding assembly parts, and welded construction. 本标准规定的一般尺寸公差和形位公差适用于焊件、焊接组装件和焊接结构。
- The mathematical models of evaluating profile error of any surface take by CMMS are proposed, these methods has been proved fitting for the geometrical tolerances standard by using optimization edited in Turbo C. 介绍了在三坐标测量机上测量和评定面轮廓度误差的数学模型 ,和应用最优化方法用TurboC语言编制的计算机程序 ,经校核验证 ,该算法符合形位公差国家标准的有关规定。
- A Superficial Coent on the Direction and Position of Geometrical Tolerance Zone 浅谈形位公差带的方向与方位
- Geometrical tolerance logical choice and accurate label at the products design 产品设计中形位公差的合理选用与正确标注
- Based on the national standards on geometric tolerance, the paper analyses the significance of ER (Envelope Requirement), MMR (Maximum Material Requirement) and LMR(Least Material Requirement). 本文根据形位公差国家标准的有关规定,剖析了包容要求、最大实体要求和最小实体要求的含义。
- Geometrical theorems grew out of empirical methods. 几何定理是从经验得出的。
- This has gone beyond the gauge of her tolerance. 这已超出她的忍受范围。
- Profile of a surface is the only geometric tolerance that locates surfaces.The orientation tolerances of perpendicularity, parallelism and angularity never locate features. 垂直度，平行度和倾斜度这三种定向公差都不能控制特征的位置，我们可以采用给出基准要求的面轮廓度来控制特征的位置。
- Seen from above, the fields looked like a geometrical pattern. 从上面往下看,那些农田像是几何图案。
- Draft allowances can be incorporated into dimensional tolerances or geometric tolerances only upon consultation with the foundry. 拔模斜度余量只有经与铸造厂商定后才能合并到尺寸公差或形位公差中。
- Try to discuss again the relation between geometrical tolerance and the dimensional tolerance 再谈形位公差与尺寸公差之间的关系
- A Superficial Comment on Five Factor Method of Analysis for Geometrical Tolerance Zone 浅谈形位公差带的五因素分析法
- Physiological tolerance to a drug resulting from repeated use. 适应性由于长期使用某种药物而产生的对该药的生理上的耐药性
- This machine part was built to a tolerance of 0.01 millimeters. 这一机器部件的制造公差是0.;01毫米。
- In ordinary living there can be some tolerance of unpunctuality. 在平常的生活中，对不准时的行为可以给予一些宽容。
- Lacking tolerance, breadth of view, or sympathy; petty. 才智有限的缺乏忍耐力、认识深度或同情心的; 气量小的
