您要查找的是不是：
- Adjustment using direct force measurement. 使用直接测力法来调整。
- Using Centrifugal Force Measure Quickly Weighing. 应用离心力测量的快速称重。
- Existing AFMs, however, have limited resolution because the force measurements must be averaged over time. 不过，现存AFM的解析度很有限，因为测得的作用力必须除以时间来求平均值。
- The force measuring unit works on the hydraulic principle. 力测量单元是基于液压原理工作的。
- Difference between end value and start value of a force measuring range. 测量范围的终值与初始值之间的差值。
- Single molecule force spectroscopy (SMFS) is a force measurement based on AFM. 单分子力谱是基于原子力显微镜力的测量方法。
- The low-profile design combined with innovative introduction of force endow this force transducer with significant advantages for use in scales and for force measurements of all kinds. 小剖面高度设计加上力的创新性引入方式使得这款力传感器在称重方面的应用和各类力的测量中具有显著优势。
- The flow quality and performance of instrumentation of the AT-303 wind tunnel have been checked by testing the HB-2(AGARD) reference model with force measurements and comparing the results obtained with available experimental and numerical data. 在ITAM与ESTEC和EADS-ST协作的ISTC项目的框架下,在AT303风洞中对不同航天飞行器的空气动力特性进行了研究。 通过对HB-2(AGARD)参考模型进行测力实验,并将实验结果与其它可用的实验和数值计算结果进行比较,AT-303风洞的流场品质和实验仪器的性能得到了检验。
- Force measurements must be taken of each surrogate lighter before and after each 100 child panel to verify that they are within easonable operationg tolerances for a production lighter. 在打火机样备100个儿童测试代表测试前后要进行压力测试，以确保打火机在其可承受的压力范围那轻松操作。
- In order to solve the problem that dynamometer can't be directly used for intelligent NC machining. the feed motor current is employed for indirect cutting force measurements with this model. 针对智能化数控加工中测力平台并不实用的问题，应用该模型和交流伺服电机电流进行切削力的间接测量。
- Analvsis of stress and stiffness of the treadling force measurement device by F. E. M. 运动员脚蹬力测定装置的强、刚度分析。
- Manufactured to fit - accurate and reliable force measurement in extremely difficult environments. 来满足-实现极端困难环境下精确可靠的力测量。
- Thin-film sensors are ideally suited to force measurement in complex geometries. 薄膜传感器是复杂几何形状的结构中测量力度的理想选择。
- The hydraulic force measuring devices are exclusively intended for measuring static chucking force at rotating chucks. 液压测力仪是专为测量旋转卡盘中静态夹紧力设计的。
- This article deals with the principle and method of the making of the pressductor on a force measuring device. 本文介绍压磁式测力传感器的制作原理和方法。
- The door may be supported in a horizontal plane during the pull force measurement test. 在拉力测量期间，可以在水平面内对门进行支承。
- Some have been produced artificially through some extremely forceful measures. 一些已经通过一些有力的措施人工制造。
- Bearing in mind the life of the force measuring unit a force measuring unit with a somewhat larger working range should be chosen. 请记住适用范围较大的测力单元将是更好的选择。
- European standard EN 1550 prescribes the use of static chucking force measuring devices in order to make the chucking and chip removal processes safe. 欧洲EN 1550标准对使用静态夹紧力测量仪测量自动定心卡盘做出了规定,保证夹紧状态和切屑清除过程的安全。
- Chucking force is recorded in a simple, low-cost way in selfcentring chucks using these hydraulic force measuring devices, and directly displayed. 自动定心卡盘的夹紧力用这些液压测力设备测量时可以用简单而低耗的方法进行记录,并且能够直接显示。
