您要查找的是不是：
- Test Method for Fluorescent Liquid Penetrant Examination Using the Hydrophilic Post-Emulsification Process 亲水性后乳化型荧光液体渗透检查试验方法
- Test Method for Fluorescent Liquid Penetrant Examination Using the Lipophilic Post-Emulsification Process 亲油性后乳化型荧光液体渗透检查试验方法
- Test Method for Fluorescent Liquid Penetrant Examination Using the Solvent-Removable Process 溶剂去除型荧光液体渗透检查试验方法
- Test Method for Fluorescent Liquid Penetrant Examination Using the Water-Washable Process 水洗型荧光液体渗透检查试验方法
- fluorescent liquid penetrant 荧光液体渗透剂
- Founding. Liquid penetrant inspection. Part 1: sand, gravity die and low pressure die castings. 铸造。液体渗透检验。第1部分:砂模铸件、压铸件和低压模铸件。
- Removal of defects shall be verified by magnetic particle or liquid penetrant examination. 用磁粉或渗透检测缺陷是否清除。
- Liquid penetrant may be used for inspection of defect excavations on all grades. 液体渗透检测可检查所有级别的空洞缺陷。
- Which of the test part characteristics listed below are normally considered before the specific liquid penetrant test method is selected? 选择液体渗透试制方法时，通常要考虑下面列出的哪些零件特性？
- All attachment areas in ferromagnetic materials shall be examined by the magnetic particle technique, if this is not possible by liquid penetrant methods. 铁磁体材料上所有粘附表面，若不能作渗透检测，可采用磁粉检测方法。
- Simulated by WSI at 5G position, the INCONEL 52M TIG weld passed Liquid Penetrant inspection (LP) and Ultrasonic test (UT) thoroughly, no any defects observed. 经WSI模拟5G位置TIG焊测试,INCONEL52M的TIG 焊缝完全通过液体渗透探伤(LP)和超声波探伤(UT),未发现任何缺陷。
- After the workpiece has been cleaned, liquid penetrant is applied in a suitable manner so as to form a film of the penetrant over the surface for at least 13mm beyond the area being inspected. 渗透：待工件清洁干净后，渗透剂就需要以一种合适的方式施加，以便在超过被检区域至少13毫米的表面上获得一薄层渗透剂。
- RELIABILITY OF LIQUID PENETRANT INSPECTION 液体渗透检测的可靠性
- Test Method for Liquid Penetrant Examination 液体渗透检验标准试验方法
- The liquid penetration method, procedure, defect indication and indication characters of pipe welds in boiler were described simply in this article. 对锅炉管道焊缝液体渗透检测方法、操作程序、缺陷显示及痕迹特征作了简单介绍。
- The relation between viscosity and flow rate of liquid penetrating through porous material was investigated by using available datu. 利用现有的资料，对液体透过多孔材料时的液体粘度与流量的关系进行了研究。
- Most synthetic detergents are in the form of powder or liquid. 大多数合成洗涤剂呈粉状或液态。
- Be careful not to lose too much liquid by evaporation. 小心，不要因为蒸发作用而失掉过多的水份。
- The surface of the liquid gradually crusted over. 液体表面渐渐地结了一层皮。
- The dregs settled and the liquid became clear. 渣滓沉淀下来，液体变清了。
