您要查找的是不是：
- flange outer diameter 法兰外径
- Measure the inner and outer diameter of big pipe. 用于测量大口径长钢管的内外径测量。
- Axial pullout of the screws is determined by the outer diameter of the screw. 螺钉的轴向拔出力由螺钉外径决定。
- Third, polish treatment of the billet can obtain the best flange outer protruding shape and the best bottom flatness in the dry friction condition. 第三、在乾摩擦条件下若素材之表面加以抛光处理，可以获得最佳凸缘外形轮廓和最佳的凸缘底面。
- The effective diameter of the motor pulley is obtained by subtracting 5 mm from the outer diameter. 马达皮带轮的有效直径为外径减5mm的数值。
- Lubricate the inner and outer diameter of the gasket with the lubricant provided or a similar non-petroleum base water soluble grease. 用所提供的润滑油或类似的非石油基水溶性润滑脂润滑垫圈的内径和外径。
- Apply silicon sealer/lubricant to the inner and outer diameters of the flange kit gasket, and press the gasket onto the valve body end. 将硅密封/润滑剂施加在法兰组件垫圈的内径和外径上，将垫圈压在阀体端口上。
- Note: The front two numbers indicate the inner diameter of the pipe, and the back two indicate the outer diameter. 说明:前两位数表示管子内径,后两位数表示管子外径。
- Allowed bending radius not smaller than 6 times of its outer diameter, laying temperature not lower than 0. 电缆允许弯曲关径应不小于电缆外径的6倍,敷设温度应不低于0。
- When using a motor of 2P, use the motor pulley, the outer diameter of which is 50mm or less. 使用2P马达时，请使用外径50mm以下的马达皮带轮。
- The relationships between the reduction of outer diameter of the containers and the ratio of the ex... 对所给予的总冲击能来说,由容器的材料和几何形状来决定。
- It should be realised that ovalisation of the 22mm outer diameter pipes was minimal and difficult to measure. 显然，22毫米外径管的成椭圆形是最小的且难以测量。
- A.For annealed drawn tubes the ratio of outer diameter to thickness is no more than 15. 退火态拉制管外径与壁厚之比不小于15者。
- After dividing into subcostal artery, the outer diameter of 67 percent of subcostal artery was bigger than that of inferior abdomen arteries. 发出肋缘动脉后67%25的肋缘动脉比腹壁下动脉本干粗。
- Being rotated around the fixed axis of the tire with aeration, the outer diameter is increased whereas sidewalls are reduced relative to being aerated. 轮胎充气且定轴转动时，由于离心力的作用，轮胎外直径和胎冠曲率比静止充气时增大，而断面宽和胎侧曲率则比静止充气时有所减小。
- The finite element model was made by considering the influence of fins geometry, radius at the bottom of the fins, and the rate of length to outer diameter of tube. 模拟低翅片管在换热器中的工作状态，得到低翅片管在四种约束模态下固有频率的有限元计算值。
- Uses in rubbing on the material negative camber grinder,is suitable the surface broadly,grinding strength.According to product radian different definite outer diameter size. 用于摩擦材料内弧磨床上，适用面广、磨削力强，根据产品弧度不同确定外径大小。
- There is relationship between the accuracy of rolle base face and its outer diameter surface. Inexorable law between they two was discussed,and relative formulas were given. 圆锥滚子基面与其外径表面的精度之间存在着联系;探讨了两者间必然规律;给出了公式.
- Tolerance on outer diameter and wall thickness should be observed,but for the following two circum stances,shorter axis should not be less than 95% of nominal diameter. 管材的不圆和壁厚不匀，应不超出外径的壁厚允许偏差，但属下列两种情况之一者，其短轴尺寸应不小于公称外径的95%25。
- The analysis results suggest that the flexural strength and torsional strength are best,as the thickness of the hollow spindle is around 2/7 of the outer diameter of the spindles. 计算结果表明,当空心轴的壁厚约为其外径的2/7时,其主轴的抗扭、抗弯性能最好,而且使用的材料最少;
