您要查找的是不是：
- flange gasket residual stress 法兰垫残余应力
- The slight decrease in the spools length is to accommodate the flange gasket, approximately 1/8". 稍微增加短管长度以适应法兰垫圈，大约1/8英寸。
- The urethane liner extends over the flange face to serve as the valve's flange gasket. 这种氨基甲酸乙酯延展覆盖到法兰表面，起到阀门法兰衬垫的作用。
- This paper demonstrates residual stress of induction quench parts and personal views about stress distribution of flange corner heat treatment ,truck half axle material and depth of hardened layer. 论述了感应淬火零件的残余应力形态,并对载货车半轴的材料、硬化层深度及法兰圆角淬火层分布提出了个人见解。
- The distribution of residual stress of weld joints is analyzed. 并分析了焊接接头残余应力的分布规律。
- Note: The flange gasket bolts for the gate valves should be retightened during installation as the bolts may have loosened due to storage and shipping. 注意:闸阀的法兰垫圈螺栓在安装期间应该重新紧固,因为在库存和运输时这些螺栓可能会松懈。
- Measurement of residual stress in multitrack laser-clad coating[J]. 引用该论文 胡木林;谢长生;黄开金.
- The flange gasket bolts for the gate valves should be retightened during installation as the bolts may have loosened due to storage and shipping. 在安装期间，闸阀上的法兰垫圈螺栓应该重新紧固，因为在库存和运输时螺栓可能会松懈。
- Residual stress is the main factor affecting the flatness of plate. 残余应力是影响矫后中厚板平直度的主要因素。
- Seat Face: Negates need for flange gaskets. 阀座表面：不需要使用阀兰垫圈。
- Installation Note: The flange gasket bolts for the gate valves should be retightened during installation as the bolts may have loosened due to storage and shipping. 安装注意事项:在安装期间,闸阀上的法兰垫圈螺栓应该重新紧固,因为在库存和运输期间螺栓可能松动。
- INSTALLATION NOTE : The flange gasket bolts for the gate valves should be retightened during installation as the bolts may have loosened due to storage and shipping. 安装注意事项:在安装期间，闸阀上的法兰垫圈螺栓应该重新紧固，因为在库存和运输期间螺栓可能松动。
- This method is also applicable to solving contact stress and residual stress. 该方法同样适用于解决接触应力和残余应力问题。
- After some steam stimulations,high residual stress is accumulated in casing. 经过几轮蒸汽吞吐,套管上会积累较高的残余应力。
- Compressive residual stress are the main factor in the increase of torsion fatigue limit. 喷丸后扭转疲劳极限提高的主要原因是残余压应力的作用。
- Considerable residual stresses exist in the normal direction. 在其厚度方向存在着可观的残余应力。
- A common method of creating a beneficial residual stress pattern is by peening the surface. 一个产生有盖的残余应力模型的常用方法是向材料表面喷丸。
- water pump outlet valve flange gasket 水泵出口阀法兰垫片
- nozzle flange gasket face (surface) 接管法兰密封面
- Stress tempering the operating die casting die will reduce the level of accumulate residual stress. 压铸模具经因长期使用而累积之应力可用回火处理消减。
