您要查找的是不是：
- The slight decrease in the spools length is to accommodate the flange gasket, approximately 1/8". 稍微增加短管长度以适应法兰垫圈，大约1/8英寸。
- The urethane liner extends over the flange face to serve as the valve's flange gasket. 这种氨基甲酸乙酯延展覆盖到法兰表面，起到阀门法兰衬垫的作用。
- Note: The flange gasket bolts for the gate valves should be retightened during installation as the bolts may have loosened due to storage and shipping. 注意:闸阀的法兰垫圈螺栓在安装期间应该重新紧固,因为在库存和运输时这些螺栓可能会松懈。
- The flange gasket bolts for the gate valves should be retightened during installation as the bolts may have loosened due to storage and shipping. 在安装期间，闸阀上的法兰垫圈螺栓应该重新紧固，因为在库存和运输时螺栓可能会松懈。
- Installation Note: The flange gasket bolts for the gate valves should be retightened during installation as the bolts may have loosened due to storage and shipping. 安装注意事项:在安装期间,闸阀上的法兰垫圈螺栓应该重新紧固,因为在库存和运输期间螺栓可能松动。
- Seat Face: Negates need for flange gaskets. 阀座表面：不需要使用阀兰垫圈。
- INSTALLATION NOTE : The flange gasket bolts for the gate valves should be retightened during installation as the bolts may have loosened due to storage and shipping. 安装注意事项:在安装期间，闸阀上的法兰垫圈螺栓应该重新紧固，因为在库存和运输期间螺栓可能松动。
- water pump outlet valve flange gasket 水泵出口阀法兰垫片
- nozzle flange gasket face (surface) 接管法兰密封面
- Flange gaskets are not interchangeable with other mechanical pipe couplings or flange gaskets. 法兰垫圈与其它机械管道连接器或法兰垫圈互换。
- In the use of the process, if the fill-han, flange gaskets and other parts of the formation of cracks or leaks that may arise on the micropore. 在使用过程中，如果在填料涵、法兰垫片等部位形成缝隙或微孔就可能产生泄漏。
- Install this valve between any ANSI Class 125 or 150 flange. Cast iron, bronze, plastic or steel flanges may be used. No flange gaskets are required. 安装在ANSI标准125或150磅级法兰之间。也可采用铸铁，青铜，塑料或钢法兰。不需要法兰垫圈。
- USE THIS VALVE ONLY WITH FLAT FACE FLANGE AND FULL FACE GASKET. 这种阀门只能与平面法兰和全工作面垫圈配合使用。
- INVALIDATION REASONS OF FLANGE GASKET ON THE TOP OF REVERSE-SPRAYING PIPE IN THE DYNA-WAVE SYSTEM 动力波系统逆喷管顶部法兰垫圈失效原因分析与对策
- Study on Principle of Designing a Flange Gasket with Flexible Graphite Sealing Material 柔性石墨密封材料制作法兰密封垫机理研究
- 7) Seat Face: Negates need for flange gaskets. 阀座表面：不需要使用阀兰垫圈。
- A flat ring made of rubber or plastic, used as a gasket. O型环一种由橡胶或塑料制成的平环，用作垫圈
- Remove and replace the O-ring and gasket. 拆卸和更换O形环和垫圈。
- This collar acts as a kind of gasket. 这个翻边起一种密封垫的作用。
- Only one set of flange studs is needed. 只需要一套法兰柱头螺栓。
