您要查找的是不是：
- Tests and analysis of exit temperature distribution of the combustor for missile turbojet 弹用涡喷发动机燃烧室出口温度场试验与分析
- exit temperature distribution 出口温度分布
- The temperature distribution of flameholders shows that high temperature area of narrow jet exit EBMC flameholders is bigger. 从出口温度分布可以看出，缝宽小的尾缘吹气式稳定器高温区域较大；
- The control objective for the stirred-tank heater is to keep the exit temperature T at a constant reference value T. 控制宗旨为搅动坦克加热器将保留出口温度T在一个恒定的参考价值T。
- Steady-state laser heating: estimation of the temperature distribution. 稳定状态的激光加热:温度分配的估算。
- Variations of beth evaporating temperature and gas-cooler exit temperature have strong impacts on the EER of the system. 蒸发温度和气体冷却器出口温度两工况的变化对该系统性能的影响程度相对较大。
- Flatting of Temperature Distribution in Laser Induced Diffusion Region[J]. 引用该论文 吴云峰;叶玉堂;王兵学;杨先明;秦宇伟.
- The problems of setting value self-tunning of mill load and exit temperature and alarming of empty and full mill are also discussed. 本文还讨论了磨负荷、出口温度给定值的自修正及空、满磨报警等问题。
- Title： Temperature distribution inside wood during microwave-vacuum drying. 关键词：微波真空;木材;干燥;温度分布
- Temperature distribution of monocline laser crystal in operation process[J]. 引用该论文 沈鸿元;张戈;黄呈辉;位民;陈振强.
- An analogism method was put forward, so by this means the estimate of exit temperature which changed along with the aperture of mixing hole became more accurate. 利用气动函数结合流阻法进行流动参数计算，采用气动方法计算射流穿透深度和掺混温度，得出相应掺混孔改变量与掺混气变化量及相应燃烧室出口截面处的温度变化量。
- In this paper, a new-type coil heat exchanger is designed and the exit temperature is guaranteed high enough by full forced convection both inside and outside of the coiler. 本文设计了不带搅拌的新型蛇管换热器,并通过保证蛇管内外充分的强制对流来保证油剂达到足够的出口温度。
- The experimental results show that in the process of flow excursion the mass flow rate and the inlet temperature decreases,while the exit temperature increases smoothly. 研究结果表明：在发生静态流量漂移时，系统循环流量下降、加热段的进口温度下降而出口温度上升；
- The principal factors affecting the exit temperature of the slabs such as slab size, volume of secondary cooling water and mode of cooling are analyzed.It is conc... 应用该模型分析了影响板坯出连铸机温度的主要因素:板坯尺寸、拉速、二冷水量及冷却方式等。
- Temperature distribution of the model is obtained, in which "skin effect theory" described in ASME code is verified. 分析了管板模型的温度场分布规律，验证了ASME规范中表皮效应理论；
- The main purpose of this software is to provide a correct initial temperature distribut... 该简化算法运算时间短，可以满足实际应用中对运算时间的要求。
- In addition,the temperature distribute on radial and on exit field of combustor were presented.It is useful for the hot design of the turbine nozzle blades. 分析结论可以用于弹用涡喷发动机燃烧室出口温度场预测和涡轮导向器叶片热设计。
- The temperature distribution in runner is complex because of the numerous effect factors. 熔体内温度分布较为复杂,影响因素众多。
- The predicted results showed that maximum combustion temperature, smog exit temperature, maximum wall heat flux and averaged wall heat flux would increase with increasing phosphorus mass flow rate when excess-air coefficient or air flow rate was constant. 模拟结果表明，无论过剩空气系数固定还是空气流量固定，随燃磷量的增大，最高燃烧温度、烟气出口温度、壁面平均热流和最大热流都呈上升趋势。
- Applications: profiling and calibration and recording the temperature distribution in ovens ,furnaces. 用途：用于回流焊、烧结、钎焊等窑炉炉膛温度分布的测试、记录和标定。
