您要查找的是不是：
- excessive heat generating cold 热极生寒
- excessive heat generating wind 热极生风, 热盛风动
- A failure in a device attributable to burning, excessive heat, or friction. 烧毁，烧坏由于燃烧、超高热或摩擦引起的设备故障
- Carrier oils should be cold pressed to ensure that vitamins and therapeutic fatty acids are not destroyed due to excessive heat. 要选用冷压的底油以免底油里的维他命和有冶疗效用的脂肪酸受热而被破坏。
- YScan transformers for excessive heat and hot spots. 扫描变压器,检查不正常的发热和热点。
- Fast cooling speed was the main reason of generating cold crackle. 认为冷却速度过快是产生冷裂纹的主要原因。
- But the ULV processor is not expected to generate excessive heat. 但是ULV（超低电压）的处理器，预期应该不会产生过度的热量。
- Removal of excess heat is accomplished by means of a radiator. 通过散热器完成多余热量的排出。
- Women run about half a degree higher after ovulation. With menopause the female thermostat imagining excess heat where none exists, generating unnecessary sweat. 女性排卵后，体温约升高半度。停经后，女性的温度调节器会想像体内藏著其实并不存在的多馀热量，于是产生不必要的汗。
- Our environment contains several factors that may cause disease. Even the weather can be dangerous. Too much cold may result in frostbite. Excessive heat may produce heat exhaustion. 我们的环境包含若干可能引起疾病的因素。甚至天气都可能是危险的。严寒可造成冻伤。炎热可导致中暑。
- Avoid excessive heating of cast fittings. 铸造管件要避免加热过度。
- Heat exhaustion (or heat prostration): Response of the body to excessive heat. 热衰竭:身体对过热的反应。
- Forecasters issued an excessive heat warning for parts of Washington State. 气象预报员发布华盛顿州部分地区超高温警报。
- With controlled pace and sequence of construction, excess heat disperses. 在对施工进度和程序加以控制之后，多余的热量就能散掉。
- Basement boilers produce the steam, and holes in the dome release excess heat. 地下室的锅炉产生蒸汽，然后通过圆屋顶的孔释放多余的热量。
- Heat: A small amount of heat generated in the reaction. 热:反应产生了小量的热。
- The unforeseen intense heat generated by the high quality concrete, grade bn.550 and bn.450, was overcome by cooling with inlaid cold water pipes. 事先没有预料到标号为BN550和BN450的优质混凝土会产生很高的温度,后来采用内嵌冷水管冷却解决了这一问题。
- The unforeseen intense heat generated by the high quality concrete, grade BN 550 and BN 450, was overcome by cooling with inlaid cold water pipes. 事先没有预料到标号为bn550和bn450的优质混凝土会产生很高的温度,后来采用内嵌冷水管冷却解决了这一问题。
- Heat solder joints only to the point were solder will flow properly. Excessive heat may distort brass castings. 热焊料连接只能用在焊料能够正确流动的地方。过热可能扭曲黄铜铸件。
- It did not furnish an explantation for the heat generated by friction. 它未能圆满地解释因摩擦而产生的热。
