您要查找的是不是：
- elongation at yield point 屈服点伸长
- When acetanilide content was 20%, the elongation at break point rose to about 10 times of pure PVC. 当乙酰苯胺质量分数为20%25时，材料的断裂伸长率增大至纯PVC的10倍左右。
- elongation at yield 屈服伸长
- The influence of thermal oxygen on the tensile yield stress, tensile breaking stress, impact strength, elongation at break , melt point and the heat of melting of PF Nylon 1212 is investigated. 通过热氧老化试验,考察了热氧对尼龙1212拉伸屈服应力、拉伸断裂应力、冲击强度、断裂伸长率、熔点、熔融热的影响。
- The elongation at break is increased and the specimen may neck before fracture. 断裂伸长增加，试验出现细颈状，然后断裂。
- Used for testing breaking tenacity and elongation at break of raw silk in skein and bobbin. 用于测定绞装和筒装生丝的断裂强度及断裂伸长率。
- Rubber- or plastics-coated fabrics. Determination of tensile strength and elongation at break. 橡胶或塑料涂层织物。拉伸强度和断裂伸长的测定。
- The tensile strength for LLDPE/EVA blends increases as ATH content is increased,but elongation at break decreases. 随着ATH含量的增加,LLDPE/EVA共混物的拉伸强度逐步增加,断裂伸长率迅速下降。
- It was observed that the lower yield point was subject to a greater degree of scatter than that of the upper yield point. 业已观察到下屈服点比上屈服点易产生更大的散布度。
- The tensile strength and elongation at break of NR were improved by addition of small amount of OMMT,... OMMT对复合材料的硫化表现出促进作用,但其含量对复合材料的硫化特性影响不大。
- The yield point represents the dividing line or transition from the elastic to the plastic region of the curve. 屈服点是弹性变形区域到塑性变形区域之间曲线的过渡点。
- Elongation at break decreases and tensile moduli increases with the PVC increase. 两种增容剂增容的体系，随着PVC加入量的增加，拉伸强度下降不明显、断裂伸长率随着PVC的增加而降低，在50 wt%25以前冲击强度保持较高数值，之后显著下降，弹性模量随着PVC的增加而增加。
- The yield point,quality grade and deoxidation are used to express the brands of steels, which reflects the features of engineering structural steels. 钢的牌号表示方法改为用屈服点、质量等级、脱氧程度表示，反映了工程结构钢的特点，便于使用选材。
- The tensile strength and the elongation at break of the EPDM/clay composites loading 15 phr of the organic clay reached 24.9 MPa and 666%,respectively. 有机黏土用量为15份时;试样的拉伸强度高达24.;9MPa;扯断伸长率为666%25;
- The conventional photoelastic modes and procedures suffice to indicate whether or not the yield point of the material of the prototype will be exceeded. 常用的光弹性模型和方法能够指明原型材料的屈服点是否将被超过。
- With the add of dispersant CH-10B, the tensile strength and elongation at break of PU/SiO2 nano-composites increased 48.5% and 4.2% respectively. 加入分散剂CH-10B，PU/SiO_2纳米复合材料的拉伸强度和断裂伸长率分别比未加分散剂时浙江工业大学硕士学位论文提高了48.;5%25和4
- In order to ensure that the structure is stable, the working stresses are kept well below the yield point or the proof stress. 为了保证结构稳定，工作应力应很好地保持在屈服点或弹性极限以下。
- The tensile strength and elongation at break of the PU/MCB composites can be reinforced by adding optimal content (<5%) of MCB particles. 适量改性纳米炭黑粒子明显提高了聚氨酯的拉伸强度和断裂伸长率等力学性能。
- This paper analyzed several excellent types of low yield point steel damper,including their principles,configurations,characteristics. 研究了具有高塑性低屈服点的减震器用钢化学成分、冶炼、轧制、组织和性能。
- Soft PVCproducts had a higher tensile strength, elongation at break, and better low temperature behaviorwhen mixing 5 phr EHO with 45 phr DOP. 当EHO与邻苯二甲酸二辛酯(DOP)以5:45混合使用时,可提高聚氯乙烯软制品的拉伸强度、断裂伸长率和耐寒性等性能。
