您要查找的是不是：
- dry wear resistance 干法抗磨削
- High wear resistance and good toughness properties. 具有高的耐磨性和良好的韧性。
- In dry sliding the abrasive wear resistance and plough resistance of SR sample were less than that of CR one. 结果表明，在干摩擦条件下深度轧制纯铁的抗磨粒磨损性能较普通轧态纯铁差，抗犁削能力也较弱；
- Highest wear resistance for low strain of toughness. 具有最高的耐磨性、在低应力条件下具有最好的韧性。
- For high strain of toughness and good wear resistance. 在高应力条件下具有好的韧性和高的耐磨性。
- Good characteristics for toughness and wear resistance. 具有好的耐磨损和韧性。
- It has a hard and tough film, wear resistance and excellent colour retention. 具有漆膜坚硬、耐磨,保色性好等特点。
- Wear resistant ceramics machine parts. 耐磨陶瓷用作机械零件。
- Urumqi Xinzhou Wear Resistant Material Co., Ltd. 新轴耐磨材料有限公司。
- ER5 is a cold work die steel with high wear resistance and toughness. ER5是一种高耐磨冷作模具钢。
- The wear resistance of in-situ Ti-TiC-TiB composites were investigated. 采用摩擦磨损试验机检测了两种材料的抗磨损性能。
- Good hardness and wear resistance, moderate impact resistance in the series . 辊环系列中硬度和耐磨性较高，抗冲击性适中。
- Fabrics made with velveteen, karyotyp skinpass of glossy wear resistance. 平绒的布面绒毛平整，光泽好，耐磨性好。
- LIANG Gao-fei, XU Zhen-ming, LI Jian-guo, et al.Study on dry wear behaviors of in-soti granular eutectics reinforced austenite steel matrix composites [J].Tribology,2003,23(2) :112-115. [3]梁高飞;许振明;李建国;等.;团球共晶体增强奥氏体钢基自生复合材料的干摩擦磨损行为研究[J]
- Recommended for important wear resistant structures. 本产品可推广应用于重要的耐磨钢结构。
- The cutting tool must be strong, tough, hard, and wear resistant. 刀具必须具有强度、硬度、韧性和耐磨性。
- Drug resistance,dustproof,seamless safety,hyguiene,non-toxic,odurless,easy to clean,goodinsulation,wear resistance. 耐药品性佳、防尘、平滑无接缝、安全、卫生、无毒、无臭、易清洁维护、绝缘、耐磨。
- The effects of heat treatment on wear resistance of disc hobbling materials of TBM have been researched using metallography and TEM. 采用金相、TEM等方法研究了热处理工艺对自行研制的全断面掘进机用盘形滚刀材料的耐磨性的影响。
- A high wear resistance is a special advantage if it permits a lower weight per unit product. 高耐磨性若能使产品减轻重量，它就有突出的优点。
- Fairly good wear resistance, primarily or small and marginally medium-sized drawing dies. 具有较好的耐用磨性,主要用于小规格,中小规格拉制模。
