您要查找的是不是：
- It is studied the existing three kinds of bearing arrangement for the driving gear shaft of locomotive motor. 摘要研究了现有的3种机车电机主动齿轮轴轴承布置方式。
- The driven gear fits its driving gear like a glove. 这个从动齿轮与它的主动轮啮合得非常好。
- The starter drive gear is mounted on the armature shaft. 启动机驱动安装在电枢转轴上的齿轮。
- driving gear shaft 主动齿轮轴
- transmission drive gear shaft 变速器主动齿轮轴
- A driving gear is different from a drive gear. 一个主动轮是不同于一个被动轮的。
- The transmission is then moved toward the rear until the main gear shaft clears the clutch disk. It can then be lowered to the floor. 然后,把变速器主传动轴的端部从离合器中抽出,可将其放到地面上。
- The failure of a gear shaft was analyzed by SEM analysis, macrograph, metallographical examination, mechanical test, chemical analysis and etc. 摘要采用扫描电镜、低倍检验、金相检验、力学试验和化学分析等方法，分析了人字齿轮轴发生劈裂的原因。
- The numerical result showed that the length of the extended end of gear shaft has an evidential effect upon speed of losing stability of the system. 数值结果表明，齿轮轴外伸端长度对轴承的负荷分配和系统的临界转速影响十分明显，而对系统的失稳转速则影响较小。
- The remedial maintenance method for broken gear shaft of small or medium equpment is introduced.The usual using can be essured after repaired. 介绍了中小型设备齿轮轴折断的修复方法。通过装配焊接的方式修复，可保证该轴正常使用。
- Abstract The failure of a gear shaft was analyzed by SEM analysis, macrograph, metallographical examination, mechanical test, chemical analysis and etc. 摘要 采用扫描电镜、低倍检验、金相检验、力学试验和化学分析等方法，分析了人字齿轮轴发生劈裂的原因。
- The starter clutch of CAMMIS is ratchet type one, the driving gear of which is designed to double module one. 康明斯起动机单向器为棘轮式单向器,其驱动齿轮被设计成双模数制齿轮。
- Spinner mainly consisted by cabinet、wedge-shaped sheath、friction wheel、air tube clutch、gear wheel 1、gear wheel 2、gear shaft、motor pinion、air motor and other parts. 旋扣器主要有箱体、楔形套、摩擦轮、气胎离合器、轴出轴套、大齿轮1、大齿轮2、齿轮轴、马达小齿轮、气马达、继气器、箱体底盖、等组成。
- The driving mechanism transmits the torque of a single motor via a driving gear to the ink suction pump. 该驱动机构通过一驱动齿轮将一单独的电机的扭矩传递到墨水抽吸泵。
- The cold extruding process is one of the most economical and high efficiency technology for the gear shaft with involute-gear-tooth for transferring torque in automobile. 对于传递扭矩的渐开线齿形花键轴,采用冷挤压成形加工方法对其齿形部分进行近净成形加工是高效而经济的。
- The thesis presents a practical die structure with angle pin and gear shaft and rack for secondary combined inclined down loosing core of die casting hopper bodies. 在具有斜下向孔或斜下向凹凸铸件压铸模设计中,斜下向抽芯是压铸模设计的难点之一。
- As the f riction between the sliders and the two-sided fric-tional force is bigger,it ma kes the slower driving gear to get the bigger torque. 该差速器由于滑块与两侧差速轮间的摩擦力较大,使慢转驱动轮上得到了比快转驱动轮更大的转矩。另外,这种差速器综合性能好、体积小。
- Positive displacement main oil pump, mounted on bull gear shaft, oversize and arranged to protect the machine during coast down in the event of a power failure. 安装在大齿轮轴上的主油泵，超尺寸配置，以保护在突然停电时压缩机的充分润滑。
- Introduced the driving gear box for bi-directional twin screw extruder, the new thrust device can instead of the trad... 提出了用变频控制技术改造螺杆挤出机传动系统的必要性,同时闸述了改造方法和效果。
- The axial profile of an odometer driving gear(in form it's equal to an involute helicoid worm) in a certain model motorcycle is carefully analysed. 仔细分析了某型摩托车里程表主动齿轮(形式上相当于一个渐开线圆柱蜗杆)的轴向齿形。
