您要查找的是不是：
- drag force model 曳力模型
- Limits the maximum strength of the drag force. 限制拖动的最大强度。
- Force Model of Large Sized Rolling. 大型卷板机的力学模型。
- The drag force ranged 0.01-0.06dynes over Reynolds number of 11-27.These results could be used as the benchmark for floc model development. 在雷诺数11-27间受力范围为0.;01-0
- The drag force decreases as the air density decreases. 当空气密度减小时阻力也减
- By applying Morison equation and digging force formula the drag force and digging resistant force are obtained and integrated into the virtual model of underwater excavator. 利用Morison方程和挖掘力公式分别推导了水下挖掘设备所受到的水阻力和挖掘阻力,并将其引入水下挖掘机器人的虚拟模型中,对其挖掘过程进行了模拟。
- Second is article is retarded by the drag force cased by this motion. 一是微粒受到因微粒和流体介质间密度不同而产生的浮力作用；
- Having derived the fundamental drag force formula, one can derive a number of important parameters. 在导出阻力的基本公式后，就可以得出一系列重要的参数。
- Others posited that dark matter was the culprit: it might exert a gravitational or drag force. 另有些人则断定暗物质才是惹祸的元凶：它可能会对太空船施加重力或阻力。
- At last, the surface force model is provable because experimental result is close to this model. 最后，利用推导出的理论模型与得到的力学实验值作一比较，以验证其正确性。
- The compressed air powered wrench is capable of providing revert-torque to retrievable bolt end and sustain drag force. 该锚杆回收扳手由压气驱动,在给可回收锚杆的尾部提供反扭矩的同时,还可以承受拉力。
- Chapter 3 analysizes the news papering markets, and focuses on the key industry factors with the Five Force Model by Boter. 第三章，对南国今报所处的行业市场进行分析，并运用波特的“五力”竞争模型对行业关键因素进行分析。
- The difference between the drag force is compared and corrected with the distance between the porous flocs and the solid spheres. 比较污泥胶羽与实心粒子之差异，瞭解其间距离与受力关联。
- A formula for calculating the minimum underbalance in lower permeability reservoir is obtained by applying a drag force function to testing data. 通过将拖曳力函数用于油田测试数据，提出了确定低渗透地层最小测试压差的公式和方法。
- Research results are as following: The force model of oil droplet was established and the pathway of oil droplet was simulated based on the DPM model. 本文的研究对象为一种典型的卧式油气分离器。本文的主要研究工作及结论为： 建立了油滴的受力模型，应用欧拉-拉格朗日DPM模型数值模拟了油滴的运动轨迹；
- So this paper firstly introduce a predigestion of the process, and then introduce the instantaneous force model considering the abrasion of the cutter. 本文从简化工艺系统入手，对切削力进行建模，并充分考虑刀具磨损的影响。
- The parameters in the restoring force model corresponding to the design parameters of SRC member and structure are also determined. 建立了型钢砼结构(空腹式)的光滑恢复力模型参数与结构设计参数的关系；
- It can be seen from the results that, as the number of sampling increases, the skewness and kurtosis of the drag force and inertia force tend to converge. 结果表明，随着采样次数的增加，拖曳力和惯性力的偏斜度和峰度驱于收敛。
- The experimental results show that the electromagnetic force model of the Halbach actuator is comparatively accurate and the current-controlled strategy is feasible. 实验结果表明，海尔贝克型执行器的电磁力模型较准确，电流控制策略可行。
- By setting up force model of rolled stock in cutting area, function relation among clamping force, side clearance of cutting blade and side thrust is given out. 建立了轧件在剪切区的力学模型，给出了压板力、剪刃侧隙与侧推力的函数关系，并提出减小侧推力影响的对策。
