您要查找的是不是：
- double metal layers 双金属层
- This paper only details the processing of vectorization of metal layer images. 本文主要以集成电路芯片上的金属图形为例，来讨论其矢量化过程。
- In double metal cladding waveguides, the separation and degeneration of TM 0 and TM 1 modes will appear as the thickness of guiding layer increases, this may confuse the judgement of mode orders in attenuated total reflection (ATR) spectrum. 在双面金属包覆介质波导中 ,随着介质层厚度的变化 ,会出现TM0 模与TM1 模的分离和简并两种状态 ,从而影响衰减全反射 (ATR)谱中模序数的确认。
- One should cover the resistance with metal layer, to avoid the damaged during the wafer level testing. 用金属覆盖电阻,避免wafer级测试时的损伤。
- The next step is to apply a metal layer on top of the embossed pits or wobbled groove. 下一个步骤是在塑料基片的浮雕坑型或摆动槽的上面覆盖一个金属层。
- We often use multilevel drawbench.It is very compatible that the multilevel drawbench draws the different intension coefficient double metal. 同时,多级拉丝系统在拉拔抗拉强度系数不同的双金属丝时,也非常适用。
- The metal layer was described in distributing, thickness and visage by the method of EPMA. 利用电子探针分析了在不同条件下 ;环氧树脂表面所沉积的金属层的形貌、表面成分和金属沉积层厚度 .
- The content of Fe and Zn of the double metal catalyst for the preparation of polyether were measured by using complex titration analysis method. 研究了用配位滴定分析方法测定聚醚多元醇用双金属催化剂中锌、铁含量的方法。
- The thickness of metal layer can be confirmed by admittance loci illustrate method. 应用导纳轨迹图解方法,可以确定能诱导出滤光片最大透射率的金属层厚度。
- The material and technology of manufacture of screw slag removre of double metal high Cr castiron and carbon steel have been investigated. 研究了制造高铬铸铁碳钢双金属复合排渣器的材料与工艺。
- Polyether polyols with high mlecular weigh, marrow molecular distribution and low monolwere prepared by using a double metal cyanide catalyst. 使用双金属氰化物络合催化剂，制备了分子量高、分子量分布窄、不饱和度低的低单官能度聚醚多元醇。
- In the deep submicrometer design, with the increase of metal layer and the reduced width of line, the circuit performance and density have been improved greatly. 摘要集成电路设计进入了超深亚微米领域，金属层增加，线宽减小，使电路的性能和密度都得到了很大的提高，但也引入了愈来愈严重的互连线效应，并最终引发了信号完整性问题。
- This paper introduced the sheet metal layered incremental forming process. 摘要本文介绍了金属板材分层渐进成形技术。
- Effect of Nb and Cu metal layer thickness on microstructure and property of Si3N4/Nb/Cu/Ni/Inconel 600 joint[J].Transactions of the China Welding Institution,2005,26(7):54-58. Nb;Cu金属层厚度对Si3N4/Nb/Cu/Ni/Inconel 600接头组织和性能的影响[J].;焊接学报;2005;26(7):54-58
- FEM simulation of sheet metal layered forming process has been introduced. 介绍了金属板料分层渐进成形过程有限元模拟。
- The experiment results show that under reaction temperature 80 C and reaction pressure 3.0 MPa, the reaction conversion is nearly 100% and the yield is beyond 90.0% with Ni-Co/C double metal supported catalyst. 实验表明，在温度110℃，压力3.;0MPa下，采用Ni-Co/C催化剂进行的加氢催化反应，原料转化率近于100%25，产物收率在90%25以上。
- The polyether polyols which has higher molecular weight,narrower molecular weight distribution and lower unsaturation can be prepared by using double metal cyanide (DMC) complex catalysts. 用双金属氰化物(DMC)络合催化剂可制得相对分子质量高、相对分子质量分布窄和不饱和度低的聚醚多元醇。
- When voltage is applied to a metallic layer between the plates,it warms up and radiates heat to the room. 当电流通过玻璃板之间的金属层时，加热器升温并将热量向房间辐射。
- Poly (propylene carbonate) polyols was synthesized by the copolymerization of carbon dioxide with propylene oxide in the presence of double metallic catalyst in loop reactor. 摘要以二氧化碳3环氧丙烷为原材料，在双金属氰化物催化剂催化下，利用环流反应器合成聚碳酸亚丙酯多元醇。
- Copper, lead and zinc chiefly exist in sulfides or sulfo_arsenides and are concentrated in the metallic layer. 铜、铅、锌主要以硫化物和硫砷化物等存在，多富集在金属层中。
