您要查找的是不是：
- Research on location of the distribution oil hole 配油孔定位研究
- distribution oil hole 配油孔
- There is one oil groove in the bronze bushing, where lubricant can flow into the axis from the oil hole on the cap of housings. 轴瓦内表面的不承担载荷部分开有油槽，润滑油通过进油孔和邮沟流进间隙。
- The oil hole is small and deep, so it is very difficult to machining. and we will try to take the broken aiguille out, and end it as soon. 因为油孔又小又深，加工难度本身很大，我方将尽快把断在里面钻头取出来就算完工。
- The fracture of stuffing box was caused by fatigue, which resulted from the maximum stress concentration on the centripetal border of the oil hole. 结果表明：材料成分和显微组织均符合要求；裂纹起源于输油孔的侧壁；填料盘的失效模式为疲劳失效，内压在填料盘内部输油孔上产生的应力集中导致了填料盘的疲劳失效。
- A kind of Rotary cultivator shell, it includes shell with transmission shaft axis hole and set oil hole, set oil hole end has end cover , magnet is in this end cover . 一种旋耕机机壳，它包括带有传动轴轴孔及放油孔的壳体,放油孔端头设有端盖，在该端盖内设有磁铁。
- This article introduces mainly calculation of a slanting angle of crankshaft clamping with the analysis method in machining crankshaft oblique oil hole. 主要介绍在加工发动机曲轴斜油孔时,用解析法计算曲轴装夹时所倾斜的角度。
- Main olein product: Camellia-oil, fragrant sesame oil, well distributed oil, rapeseed oil, peanut oil. 主要油脂产品：山茶油、香麻油、调和油、菜籽油、花生油。
- Distribution Oil Cutouts and Fuse Links 配电用油断路器和熔断体
- The Iraqi government is distributing oil revenues across the country, so that reconstruction can follow hard-won security gains. 伊拉克政府全国各地分布油收支,以便重建可能跟随来之不易的安全获取。
- Improvement in Piston Pin Boss Oil Hole Machining 活塞销座油孔加工方法改进
- FAW TOYOTA engine company crankshaft product line uses carbide tool and MQL technique to process crankshaft oil holes. 一汽丰田(长春)发动机有限公司曲轴生产线采用硬质合金钻头并配合半干式加工(MQL)技术加工曲轴油孔。
- steering column jacket oil hole cover 转向轴套油孔盖
- The interval of oil changing of Variable drive is working 300h for the first time, then change oil every other 1000h, oiling to middle part of oil immersion lens from oil hole, never excess. 无级变速器首次换油时间为工作300小时，以后每隔1000小时换油，由注油孔加油至油镜中部，切勿过量。
- The distribution of the magazine is 2000. 该杂志的销售量为2000份。
- Abstract: Firstly, the understanding of realization of combustion mode control is introduced and the idea of controlling combustion mode of scramjet by distributing oil is put forwards. 本文首先介绍了对燃烧模态控制实现的认识，提出了超燃冲压发动机燃烧模态控制的配油思路。
- We have a good product but our distribution is bad. 我们的产品很好,但销售情况不佳。
- The distribution is as tabled below. 其分布情形如下表。
- Machining slanting oil hole of crankshaft with rolling process 滚轧工艺在曲轴斜油孔加工中的应用
- Design of Special Fixture of Crankshaft Oil hole and Cleaning Face 曲轴油孔和表面清洗专用夹具设计
