您要查找的是不是：
- discharge line valve 排气管线阀
- Must be connected to an adequate discharge line. 必须与适当的排泄管道连接。
- Detail of transfer line valve configuration. 传输管系统阀门配置详图。
- Must be installed to allow complete drainage of both the valve and discharge line. 必须安装到具有完全排泄能力的阀门和排泄管上。
- Must be installed to allow complete drainage of both the temperature and pressure relief valve and the discharge line. 必须正确安装,使得降温减压安全阀和排水管道都能够完全排泄。
- Must not be capped, blocked, plugged, or contain any valve between the relief valve and the end of the discharge line. 在安全阀和排泄管之间不要加盖、闭塞、堵塞或包含任何阀门。
- Close the upper pipe ram and open the kill line valve. 关上部钻杆闸板防喷器，开压井管线阀。
- Must not be smaller than the pipe size of the relief valve or have any reducing coupling installed in the discharge line. 不能小于安全阀的管道口径,也不能在排泄管上安装任何缩径管接头。
- To prevent water damage, the valve must be properly connected to a discharge line which terminates at an adequate drain. 为了防止水的破坏，这些阀门必须与排水管道连接，以便能够将水排到适当的排水口。
- Temperature and pressure relief valve properly installed with a discharge line plumbed to an open drain and protected from freezing. 正确安装降温减压安全阀，并配置排泄管引导至一个敞开的排水口，并确保不会被冻结。
- Temperature and pressure relief valve properly installed with a discharge line run to an open drain and protected from freezing. 正确安装降温减压安全阀,并配置排泄管引导至一个敞开的排水口,并确保不会被冻结。
- Important: The discharge line must be the same size as the valve outlet, and must pitch downward from the valve to a safe place for disposal. 重点提示:排泄管必须与阀门出口通径相同,必须从阀门开始向下倾斜,确保安全排放。
- Vertical discharge line must be installed with its direction downward. 必须安装垂直排泄管,其方向朝下。
- Never pipe the discharge line directly into a drainage ditch, sewer or sump. 不要把排泄管直接插入排泄地漏、污水管或污水坑里。
- Use short or standard length thermostat. Vertical discharge line must be installed with its direction downward. 适用于较短或标准长度温控杆。垂直排泄管必须安装在它的下方。
- This pipe is connected to the suction line and that one over there to the discharge line. 这根管子与上水管连通,那根管子与排水管连通。
- The end of the discharge line opening should terminate near a floor drain or other suitable location not subject to blocking or freezing. 排泄管道的终端开口必须靠近地漏或其他不会堵塞或冻结的地方。
- The installation must also allow for adequate drainage from the air gap and the discharge line if needed. 如果需要的话，还必须允许从气隙和排放管道里有适当的排放。
- A discharge line muffler is required. A suction line muffler should be package protected. 排放线上要有消音器，吸入线上的消音器必须包裹起来保护.
- This advanced technology TFM Lined valve is specially designed and produced for applications requiring high purity and maximum chemical resistance. 这种高技术TFM内衬蝶阀特别适用于要求高纯度和最高耐化学品特性的应用场合。
