您要查找的是不是：
- diesel engine cylinder block casting 发动机缸体铸件
- Improvement of Engine Cylinder Block Casting Process 提高发动机缸体铸件质量的工艺改进
- Producing and Eliminating of Pin Hole in Model 385 Cylinder Block Casting 385气缸体铸件气孔的产生与消除
- Thermal Stresses Analysis of An Engine Cylinder Block Casting Based On Finite Difference Meshes 基于有限差分网格的发动机缸体铸件热应力模拟
- Analysis and Prevention Method of Scab Defect in Cylinder Block Casting Made by Cold Core Box 冷芯盒缸体铸件内腔结疤分析与防止措施
- Development and Application of High Strength Grey Iron Automobile Engine Cylinder Block Casting 高强度灰铸铁汽车发动机缸体铸件的研制与应用
- Fromation Reason and Prevention of Scab Defect in Inner Cavity of Cylinder Block Cast with Cold Box Cores 缸体铸件内腔结疤形成原因与防止措施
- cylinder block casting 气缸体铸件
- The crankcase is the lower part of the engine cylinder block. 曲轴箱是发动机气缸体较低的部分。
- Numerical Simulation of Thermal Stress of Diesel Engine Cylinder Block Castings Under Two Different Constraints 两种不同约束条件下发动机缸体铸件热应力场的数值模拟
- Study on Dimensional Accuracy of High Strength Gray Iron Cylinder Block Castings with Thin Section Thickness 高强度薄壁灰铸铁缸体铸件尺寸精度研究
- Position the cylinder heads onto head gaskets and cylinder block. 将汽缸盖安置到汽缸盖罩垫和汽缸体上。
- Numerical Simulation of Thermal Stress in Diesel Engine Cylinder Block Castings during Solidification Process Under Different Shake-out Conditions 缸体铸件在不同落砂条件下热应力场的模拟
- Tighten the radiator draincock and (if removed), the cylinder block drain-plug. 旋紧散热器排放口和汽缸体排放塞（如果它被卸去了）。
- We are professional in casting、producing Cummis auto engine、Toyota auto engine 、Isuzu auto engine、cylinder head、cylinder block、Gearbox.aluminum wheels and other automotive products. 专业铸造、生产康明斯发动机，丰田发动机、五十铃发动机、气缸体、气缸盖、变速箱、汽车铝轮圈等产品。
- The comparison indicates that the appropriate results can be obtained only when with fine enough meshing in Finite Element modal analysis, as the cylinder block is a complex and thin cast parts. 研究表明，对于柴油机气缺体这类薄壁铸造的复杂构件，进行有限元模态分析，需要采用很细的网格划分，才能保证较精确的结果。
- The test of water simulation on the original running system verifies shows that unreasonable original running system causes blow hole in 495A diesel engine block casting. 通过对缸体原浇注工艺的水力模拟,发现原浇注工艺不合理是造成495A缸体产生缺陷的主要原因。
- Type of welding-repairing, position of weldable low alloy cast iron cylinder block,welding-repairing and sequent heat treatment process in Italian TEKSID Company have been introduced. 介绍了焊补缺陷的类型、可焊补的汽缸体部位、焊补工艺及焊后热处理工艺。
- After changing the pouring position of the casting and improving the gating system, risers and chills the acceptable ratio of the block casting has been enhanced obviously. 对浇注位置、浇注系统、冒口与冷铁等进行改进后,使该缸体铸件成品率得到了较大幅度的提高。
- Water-filled container surrounding a machine to cool it,especially that surrounding the cylinder block of an engine. 围在机器周围的冷却机器的装满水的容器，尤其用于机车的气缸柱的周围。
