您要查找的是不是：
- cycloid pump body 摆线泵泵体
- Series of flexible rotor cycloid gear pump from the main rotor, outer rotor teeth, pump body and explosion-proof motors and other components. 主要由内齿转子、外齿转子、泵体和防爆电动机等部件组成。
- Checking of the sealing injection pump body. 对喷油泵进行密封性试验。
- Especially for large pump, pump body stiffness. 特别对于大泵，泵体刚度大。
- Measurement of the internal pressure of distributor pump body. 测量分配泵泵体内压。
- Measurement of the reflux delivery of distributor pump body. 分配泵益流量测量。
- QB Clean water pump series belong to the vortex pump direct-coupled between electric machine and pump body. QB系列电动清水泵是一种高效的电动泵。
- This paper discusses the formation and properties of the inner cycloid and the principle of the tritubercular cycloidal pump is illustrated. 论述了内摆线的形成和特性及三尖摆线泵的工作原理。
- Sealing ring is fitted on pump body, while impeller sealing ring is an optional part. 设有泵体密封环，而叶轮密封环为可选用件。
- Fluid machine: pump body, pump impeller, three-way and elbow body, connector body. 流体机械：泵体，泵叶，高品质三通及弯头本体，接体本体.
- There is no need of bottom valve in pipeline, only to ensure certain priming oil in pump body before work. 管路中不需底阀，工作前只需保证泵体内储有定量引油即可。
- Pump body &pump casing made by alloy copper and stainless steel. reliable and corrosive-resist. 泵机体，马达外壳，以炮金铜及不锈钢材质制成，坚固耐蚀，轴心不锈钢304。
- This article introduces a series of special clamps for machining pump body of a Shoot Liquid Pump. 本文介绍了某种射流泵泵体加工的系列专用夹具。
- Basic types: pump body mounted on a motor directly flanged on, applicable to ordinary liquids. 基本型：泵体直接装在电机法兰上，适用于一般液体。
- In this paper,abrasion behavior of carbonitriding steels used in the manufacture of pump body is studied. 研究了碳氮共渗钢制作的水泵体的磨损特性。
- FSB series fluoroplastic alloy pump is composed of pump body, impeller, back cover, seal, support, pump shaft, bearing, coupling, fasten bolt, nut and base plate. FSB系列氟塑料合金泵由泵体、叶轮，后盖，密封性，支架，泵轴，轴承，连轴器，吊紧螺栓，螺母，底板组成。
- Non-pollution,The pump body is made of polyvinyl chloride (pvc)plastics,and the onter cover is of cold-rolled steel plate with backing finish. 无污染，本机箱体为聚氯乙稀塑料，外壳采用不锈钢和冷板静电喷塑壳两种。
- The manufacturing process of foaming mould of an oil pump body by using LOM prototype,electroforming and wire-arc spraying was introduced in detail. 以制造泵体发泡模具为例,详细介绍了在LOM原型的基础上,通过LOM原型的预处理、电铸和电弧喷涂等工艺手段快速制造发泡模具的过程。
- Swimming is the best way to tone up your body. 游泳是健体强身的最好方法。
- Based on the tooth profile curve equation of inner rotors in cycloidal pump, the formula for displacement calculation of the pump are derived. 根据摆线泵内转子的齿廓曲线方程,推导出了摆线泵的排量计算公式。
