您要查找的是不是：
- A New Type of Corrosive Wear Test Device and Its Performance Study 一种新型腐蚀磨损实验装置及其性能研究
- By means of metallograph, electronic probe, mechanical properties experiences and corrosion wear test, we analyzed the microstructure and properties of steel. 通过对试样进行力学性能、金相、电子扫描探针、腐蚀磨蚀等一系列试验，观察和分析了钢的显微组织，研究了钢的性能。
- Study on Corrosive Wear Test Machine between Oil Tube and Sucker Rod in the Oil Well 油井管杆磨蚀试验机的研制
- corrosive wear test 腐蚀耗损试验
- Zhang T C,Jiang X X,Li S Z.Performance of passivation films on stainless steels during corrosive wear process[J].Corrosion Science and Protection Technology,1998,10(5):260-262. [10]张天成;姜晓霞;李诗卓.;钝化膜在腐蚀磨损过程中的作用[J];腐蚀科学与防护技术;1998;10(5):260-262
- The raised material should be smoothed away before the commencement of the wear test. 在磨损试验开始之前应将隆起的材料弄平。
- I guess some factories would just like to give you specially made samples for wear test, right? 我想有些工厂会特别做试穿样品出对吗?
- At impact energy of 2.7 J, it is mainly spalling of extruded hardened edge for LCHA, primarily massive fatigue spalling and heavy corrosive wear for HMN and principally massive brittle spalling and heavier corrosive wear for MCA. 2 7J冲击功下,低碳高合金钢主要为挤出硬化棱的剥落,高锰钢主要为块状疲劳剥落和较严重的腐蚀磨损,中碳合金钢主要为块状脆性剥落及严重的腐蚀磨损;
- The simulation test of heavy rail straightening has been completed on M200 wear test machine. 在M200磨损试验机上对重型钢轨的矫直过程进行了模拟试验。
- The paper covers introductions of ordinary rubber wear test methods and the standards for selecting test conditions. 介绍最常用的橡胶磨耗试验方法和选择试验条件的标准。
- The materials were produced by P/M route and wear test was carried out in a MM-1000 type machine. 采用不同的烧结温度,通过粉末冶金的方法制备了铜基粉末冶金摩擦材料,在MM-1000型摩擦试验机上进行了模拟制动实验。
- Aerial craft brake movable piece produced with new heat treatment process have basically met the special requirements of wear test. 运用该工艺生产的航空刹车副动片基本满足了磨损试验的特殊要求。
- The effect of load on tribological behavior of NBR and its mechanism were studied using an pin - on - disk friction and wear test apparatus. 采用栓-盘式摩擦磨损试验机考察了载荷对丁腈橡胶摩擦学特性的影响,分析了其作用机理。
- Standard Test Method for Ranking Resistance of Plastics to Sliding Wear in Block-on-Ring Wear Test (Cumulative Wear Method) Using Micro-Tribometer mod. 标准试验方法排行抗性塑料滑动磨损块上环磨损试验（累积磨损法）利用微摩擦国防部。
- Standard Test Method for Ranking Resistance of Materials to Sliding Wear in Block-on-Ring Wear Test Using Micro-Tribometer mod. 标准试验方法排行电阻材料的滑动磨损块上环磨损试验用微摩擦国防部。
- Three kinds of methods used now by china for vulcanite wear test were introdueed brief, and their merit and defect were also compared. 简要介绍目前国内采用的硫化橡胶3种磨耗试验方法，并将其优劣加以对比。
- Result of abrasive wear test showed that wear resistance of metallurgical coating was better than that of quenched 45# steel. 实验结果表明，冶金层耐磨性比淬火45号钢有较大提高。
- A simple test will show if this is real gold. 简单的试验就能证明这是否是真金。
- The coating has a strong metallurgical boning with substrate, and the coating has high hardness, excellent wear resistance, corrosion resistance and corrosive wear resistance, so it is used widely. 合金化涂层与基体材料呈良好的冶金结合，结合强度高，能够显著提高廉价基体材料表面的硬度、耐磨性、耐蚀性和耐腐蚀磨损等性能。
- The corrosion wear resistance of low chromium white cast iron increases when the silicon content increases in it. 而增加含硅量后的低铬白口铸铁的腐蚀磨损耐磨性将比普通白口铸铁的高。
