您要查找的是不是：
- Cold Model Simulation Test on The Discharge end construction of End-discharging furnace 端出料轧钢加热炉炉头结构冷态模型实验研究
- cold model simulation 冷态模拟
- Active control of combustion instability is tested on a cold model. 首先，完成了燃烧不稳定性主动控制的冷态实验研究。
- Process model simulation helps the organization to observe how a process will perform under the variations of input. 流程模型仿真帮助组织观察在不同的输入下流程是如何执行的。
- A good agreement is shown between the model simulation and the results of the actual EAF process. 结果表明模型可与实际结果吻合得很好。
- Abstract:The slag splashing process on the 25 t LD converters, Xinyu Iron & Steel Co, was studied with a cold model. 采用缩小的冷态模型 ,对新余钢铁集团有限公司 2 5 t顶吹转炉的溅渣护炉工艺进行了研究。
- The test results of cold model verify the self-balancing property of the dipleg. 在冷态模型装置上进行的实验测定验证了料腿的自平衡效果，并获得了与理论分析相一致的结论。
- This paper probes the phenomenon by single well model simulation in fluvial depositional gas reservoir. 以河流相沉积低渗储层为例,通过单井模拟方法,探讨分析了造成上述现象的原因。
- By the model simulation,we get a basic prospection of Shanghai’s economy growth in the next few years. 通过模型模拟，我们预测了上海未来数年的经济发展概况；
- The Random Particle-Trace model Simulate the turbulence diffusion. 颗粒的湍流扩散是通过随机轨道模型来模拟的。
- An Experimental Research on the Pilot-Scale Cold Model of the Three-Stage PV Type Cyclone Separator for Acrylonitrile Reactors. 丙烯腈反应器三级PV型旋风分离器大型冷模试验研究。
- UCT biological phosphorus removal + artificial wetland model simulation run, comprehensive removal rate of 95%. UCT生物除磷+人工湿地模型综合运行的模拟实验，综合除磷率达95%25。
- The process parameters of dephophorization for 150 ton top-bottom combined blown converter at Meishan are studied with a cold model. 利用冷态模型,对梅钢150 t顶底复吹转炉脱磷工艺参数进行了研究。
- The feasibility of such a method has been validated from a theoretical analysis and checked by way of a cold model test. 从理论上分析其可行性 ,并通过冷态模化试验等研究手段进行检验。
- The motor-kinematic-acoustic deduction in the model simulation showed that the topologies were compatible from one space to another. 模型模拟的推理证明元音的拓扑结构在运动指令空间,调音空间,声学空间是相互兼容的。
- In this paper, the RSM turbulent model was applied to simulate the flow fields o f each part of the five-class cyclone preheater cold model. 采用冷模实验方法,用五孔探针对卧式旋风筒的流场分布与阻力性能进行了实验研究,对设备的性能与技术特点做出了客观评价。
- Optimal estimates of the model parameters were obtained by minimizing the difference between model simulation and experimentally measured drug release kinetics. 对模型参数的最佳评价通过最小化模型模拟和实验测定间的药物释放动力学差别来获得。
- A new entrance structure based on strong turbulence dispersion was designed and tested on a semi-industry downer cold model with 418 mm I. 基于对现有下行式循环流化床(下行床)气固混合入口的总结,提出下行床入口结构设计的关键原则。
- The original linear model can be used to analyze the stability of Pogo vibration,but the results of linear model simulation are not so satisfied. 传统的线性管路模型可以用来进行Pogo振动的稳定性分析;
- In a cold model reactor,the effects of simulated feedstock oil and gas flow on the expanding ratio of the catalyst bed were studied. 在冷模反应器内，考察了模拟原料油和气体流动对催化剂床层膨胀率的影响；
