您要查找的是不是：
- Modelling, Identification and Experimental Validation of CVT Clamping Force Control System 无级变速传动装置夹紧力控制系统建模、辨识及实验验证
- clamping force control system 夹紧力控制系统
- clamping force control 夹紧力控制
- Clamping force equalization: same force to two workpieces in different size. 自动补偿机构：不同大小工件，可在同时夹紧，且夹持力相同。
- Decoupling control is the kay technology in Direct Force Control. 解耦控制是直接力控制中最关键的技术。
- Force Sensing and Force Control Technology for Intelligent Machine System II. 智能机器系统力觉及力控制技术2。
- Size and grade specific cap bolts offer superior clamping force between the cap and base. 座罩螺栓有不同的尺寸和等级,在座罩和基础之间形成理想的夹持力。
- In using an injection moulding machine, it is best to use the minimal but adequate clamping force F. 使用注射成型机，最好使用最小同时充足的锁模力F。
- The two deices do clamping force measurement/control and caity pressure switchoer to holding pressure. 这两个装置就是锁紧力量测/控制装置和（射出）转保压的模腔压力转化装置。
- Choosing a PIMM simply on the basis of shot weight is too simplistic.Neither is clamping force alone sufficient. 仅仅基于射出重量去选择注塑机是不够的，同样的，仅考虑锁模力也不可以。
- Furthermore, a high clamping force compresses the toggles and the mould, and stretches the tiebars, reducing the fatigue lives of the toggle pins, the mould and the tiebars. 高锁模力对曲轴结构和模具产生挤压，对拉杆（控制开合模甚至锁模的四个大杆）产生拉伸，从而降低他们的疲劳寿命。
- An excessive clamping force distorts the mould and the mould cavity unnecessarily, affecting the precision of the moulded part. 过大的锁模力会使模具以及模腔产生不必要的变形，影响成型品的精度。
- Before earlier, Mcfall elects unloads the humanitarian aid commodity under the Russian force control's Batumi port. 稍早前，“麦克福尔”号选在不在俄军控制下的巴统港卸下“人道主义援助物资”。
- This paper focus on simulating the KM toolholder taper interface positioning under different clamping force by using Finite-element Method. 针对KM刀柄锥面定位在不同夹紧力下进行有限元模拟,得到径向位移、接触应力、锥面间隙结果。
- Research results show that with application of Mucell,the 10% raw material can be saved,the injection pressure is decreased by 36.7%,the clamp forc... 研究结果表明:采用微孔发泡注射成型工艺可以节省原材料10%25;注射压力降低了36.;7%25;锁模力降低了60
- It is able toovercome the defects of constant tensile force mechanism by weight and bring about tensile forc control frommachinery to electric. 该控制装置能够克服重锤式恒张力机构的缺点,实现了从机械式张力控制到电气式张力控制。
- This investigation is concerned with a servomechanism, which uses such motors for position and force control. 以多轨道之卫星影像进行影像正射化后，经镶嵌可得到大范围之正射化卫星影像。
- Twoprocess mode can be ed, single or continuous. The clamping force of hold down device will in crease when cutting force increases. 两种使用模式给客户选购，单次或连续。另压片力会随着剪切力增加而自动调节。
- The Western media concocted "military repression", "force control" But, say what? 而西方媒体炮制的“军事镇压”、“武力管制”又在说明什么？
- Its paper clamp presses tightly against the material to be cut by means of a high quality strong pull spring assembly and the clamping force can be adjusted readily. 压纸器是由优质强力拉簧组使其牢牢地压紧裁切物,压力大小调整方便。
