您要查找的是不是：
- Bolt hole fitting plastic core industrial caster. 孔顶塑芯工业脚轮。
- Lug body available with ISO flange dimensions and metric bolt hole threads. 凸耳式阀体符合ISO法兰尺寸和公制螺栓孔螺纹。
- Limited distance deviation of the optional bolt hole on flange shall be 2mm. 法兰上非强制螺栓孔的有限距离偏差应该为2毫米。
- After the valves are removed,clean the valve guide bores and all bolt holes,using a thin brush and solvent. 拆下汽门之后;用一根细刷何溶剂清理汽门导管恐核所有螺栓孔.
- The bolt holes are in the unit base. 螺栓孔在单元的基部。
- Lug body available with ISO flange dimensions and metric bolt hole threads. For dead-end service use lug style (rated 200 PSI for this service). 凸耳阀体也可配置ISO法兰尺寸和公制螺栓孔螺纹。用于终端位置可采用凸耳结构（此时额定压力为200PSI）。
- There is standard bolt hole connecting with the valve or bracket.The output axis in the middle is a standard internal octagon. 壳体上有标准的螺孔与阀门或支架相连。中间输出轴为一个标准的内八角。
- Looking for a bolt hole for you and your loved one this Valentine's Day? This selection of romantic retreats should inspire you. 充满充满波西米亚风情的广场酒店，一定会让你流连忘返。不过，要注意你的口袋哦，每天145英镑的花费，应该不算少。
- Position flywheel and O-ring on crankshaft and align bolt holes. 安装飞轮和O形环在曲轴上并对齐螺栓孔。
- Anchor/support bolt holes are located in base of body. 固定器/支架螺栓孔位于阀门的基座。
- Centerline of the slot at base of distributor is aligned to centerline of distributor holddown bolt hole on enginIn this position, the holddown bolt should easily pass through slot and into engine. 在分电盘基座上槽的中心线应与引擎上分电盘垂下螺栓孔的中心线对准。在这个位置，垂下螺栓应容易地通过槽进入引擎。
- Mount restrictor bar into the restrictor bar groove of upper die, mount adjusting bolt for restrictor bar into the bolt hole in the restrictor bar, then mount lower press block, upper press block. 在上模节流棒槽内装入节流棒，将节流棒调节螺栓装配进节流棒的螺丝孔中，再装配上压块。
- The dimension tolerance of bolt holes shall meet the following requirements. 螺栓孔的尺寸公差应满足以下要求
- Block front fork of valve disassemble tool onto cylinder head sub bolt hole, pressing this tool downwards by a force application bar until the two pieces of lock are falling down, see chart 3b. 在拆卸气门锁片时，用气门拆卸工具的前叉卡在缸盖付螺栓上，然后用加力杆向下压动气门拆卸工具，直到两锁片脱出为止，如图3b。
- His strength in a crisis is an ace in the hole. 临危不惧是他的看家本领。
- There are three lifting holes and one lifting bolt hole on thefront and rear of the machine bed for plugging lifting hooks or bars. 床身前后共有三个起重孔和一个起重螺栓孔，用以插入起重工具。
- We should brush our teeth at least twice a day. 我们每天应该至少刷两次牙。
- Note: 1.Size-Nominal diameter of the valve; D1-Diameter of the flange bolt hole center circle; D-Diameter of the flange bolt holes. 注:1.;规格尺寸为阀门通径尺寸;D1为阀门法兰孔中心分布圆尺寸;D为法兰孔直径。
- Brush off the fuzz that has blown on. 把被风吹上去的绒毛刷掉。
- The housings are horizontally split and have two or four attachment bolt holes in the base as standard. 轴承座水平剖分,底座上有两个或四个连接螺栓孔。
