您要查找的是不是：
- Two kinds of boiler design methods are developed. 開發了鍋爐設計的兩種方法。
- Analyses the causes of smoke condensation and corrosion in gas-fired hot water boilers. Points out preventing measures in boiler design and operation. 分析了燃氣熱水鍋爐煙氣結露及腐蝕原因，從鍋爐房設計與運行管理兩方面提出了預防措施。
- Known marine or land boiler very well, 3 years experience in boiler sales; Person who has working experience in shipping institute, shipyard and boiler design would be preferred. 熟悉船用或陸用鍋爐,3年以上鍋爐銷售經驗,有在船舶設計所、船廠或鍋爐設計工作經驗優先考慮。
- B&W's unique IR-CFB boiler design employs a patented two-stage particle separation system to provide high-solids loading and a uniform furnace temperature profile. 獨特的IR-CFB鍋爐設計採用獲得專利的兩級顆粒分離系統從而具備高固體份裝載和均衡的爐膛溫度。
- The pressure of sweeping shall not exceed the design pressure of the container or the piping system. 吹掃壓力不得超過容器和管道系統的設計壓力。
- These include boiler design, cooling water conditions, burner type, design steam conditions and environmental controls that capture and remove pollutants. 包括鍋爐結構、冷卻水條件、火爐類型、設計蒸汽條件和截留去除污染物質的環境管理。
- So round shape of cracks (2C/a =2)was a stable shape when cracks developed on the design pressure. 因而在設計壓力下發生裂紋傳播時,接近圓形的裂紋形狀(即2C/a=2)將是一個比較穩定的形狀。
- The seal air fans deliver a design pressure that is above the operating pressure in the flue work. 密封風機能使空氣達到設定的壓力，此壓力應高於煙氣在煙道中的運行壓力。
- A boiler designed for the pulverized coal or lignite to be consumed. 為燃燒粉狀煤或褐煤設計的鍋爐。
- All stream jackets are constructed from carbon steel materials and are welded to the valve body. Design pressure is 300 psi unless otherwise noted. 所有蒸汽套都採用碳鋼材料製造,並焊接在閥體上。除非另有指定,否則設計壓力均為300 psi。
- Reciprocating pumps and compressors require pressure relief valves when the stalling pressure exceeds cylinder design pressure. 當停轉壓力超過汽缸設計壓力的時候，往複泵和壓縮機要求安裝安全閥。
- The design features, coal properties, main systems, as well as trial operation and combustion adjustment of a 1025t/h Wshaped flame boiler in Shaoguan PowerPlant have been presented, the problems existin gin boiler design and in operation being discussed. 介紹了韶關電廠 10 2 5t/hW型火焰鍋爐的設計特性、燃煤特性、主要系統 ,以及鍋爐試運行和燃燒調整情況 ,對鍋爐設計和運行中存在的問題進行了分析。
- It is confirmed that the sinusoidal gear can be easily undercut with a specific addendum height value decided only by the design pressure angle of the gear. 經討論和模擬證實;正弦齒條所生成的齒輪在一個特定的齒頂高下最容易發生根切;該齒頂高數值只取決於正弦齒輪的設計壓力角.
- In 1983, KZL4-13 drill bar fire grate boiler designed and trail-manufactured by itself obtained national high quality product certificate. 1983年，自行設計試製的KZL4-13鑽條爐排鍋爐榮獲省優質產品證書。
- Design Pressure barg , 7.0+F.V. 表示設計壓力為：內壓7.;0，外壓全真空。
- Can argon arc root welding and manual arc cap welding be substituted with common manual arc welding on seamless steel line pipe below 5mm wall thickness with 9.5Mpa design pressure? 壁厚 5mm以下的無縫鋼管用於設計壓力9.;5MPa的管線，能否採用普通手工電弧焊工藝代替氬弧焊打底、手工電弧焊蓋面工藝施焊?
- Experienced in different boiler design disciplines 不同鍋爐設計經驗
- The simulations show that 2L-MuRR improves the RRF capacity greatly,over 70%. By using 2L-MuRR,SMT can achieve the same high performance with fewer rename registers,effectively reducing the design pressure on the register file. 模擬實驗表明;2L-MuRR顯著提高了RRF的存儲能力(70%25以上);能以較少的重命名寄存器滿足SMT高并行度的要求;有效緩解了寄存器文件的設計壓力.
- Accordingly,the least teeth number without undercutting is also decided only by the design pressure angle of the gear,without any relation to the coefficient of addendum height of the gear. 相應的無根切最少齒數也僅取決於正弦齒輪的設計壓力角;而與齒頂高係數值無關.
- Discussions on EDF 600 MW CFB Boiler Design 法國電力公司600MW超臨界CFB鍋爐設計進展
