您要查找的是不是：
- Study on the Load Cell for Bearing Load Measurement 轴承负荷测量中负荷传感器的研究
- Experiment Study on the Long-Term Stability of Bearing Load Cell in large turbine- generator sets 大型汽轮机轴承负荷传感器长期稳定性试验研究
- bearing load cell 轴承载荷传感器
- The resulting increased bearing load shortens bearing service life. 由此引起的轴承载荷的增加会缩短轴承的使用寿命。
- Bending and torsion moments can lead to permanent damage to the load cell. 弯曲和扭转会对测压元件造成永久性破坏。
- If the actual load is a combined radial and axial load, then an equivalent static bearing load must be calculated. 如实际负荷为径向和轴向复合负荷,则必须计算当量轴承静负荷。
- The specimen is mounted on a load cell which records the mass loss rate of the specimen during combustion. 这个标本是安装在称重传感器，记录燃烧过程中试样的质量损失率。
- The maximum load that can occur on a bearing should be used in the calculation of the equivalent static bearing load. 应使用轴承可能承受的最大载荷计算轴承当量静载荷。
- Both actuators are mounted below the platen with the load cell affixed to the crosshead. 这两个驱动器被安装与下面的贴在横梁称重传感器的模板。
- In all other cases it is first necessary to calculate the equivalent dynamic bearing load. 在所有其它情况下,首先需要计算当量轴承动负荷。
- Load cells ATEX certificate for zones 1 and 21 (gases and dust). 危险区1和21(气体和粉尘)的传感器ATEX防爆证书。
- Single-point, Parallel beam, Aluminium load cell; used for electronic scale， Platform and industrial weighing system. 单点平行梁结构、铝制金传感器；用于电子秤、台秤、工业秤重系统等。
- In all other cases it is necessary to first calculate the equivalent dynamic bearing load. 在所有其他情况下,必须首先计算当量轴承动负荷。
- The result indicates that the two-terminal bracing structure is optimum for bearing load and gear mesh. 计算结果表明：主动齿轮轴两端支撑结构对轴承受力和齿轮啮合最有利。
- The distinctive feature of this load cell by comparison with the others is the ring shape of the load cell piston and diaphragm. 环形测压元件与其他元件相比最大的特点是环形的测压元件活塞和膜片。
- The load cell in ring form is used for the meaurement on shafts and spindles to which a load cell of standard shape cannot be attached. 环形测压元件用于轴和杆的测量,因为普通测压元件无法对其进行测量。
- If transition at the shaft collar of a circular shaft adopting closed angle will bring biggish stress concentration as bearing load. 圆轴轴肩处若采用尖角过渡,承载时将引起较大的应力集中。
- Numerical results show that bearing load capacity can be raised by reduced clearance, enlarged eccentricity and shaft speed. 结果表明，减小轴承的间隙、提高偏心率和线速度可以使间隙内压力增大，从而提高轴承的承载能力。
- The connection line between the load cell and pressure measuring device is a rigid tube for direct assembly and a flexible tube for other kinds of assembly. 连接压力计和压强测量仪器的连接线是一根能直接装配的刚性管以及一根用于其它安装类型的软管。
- These load cells are notable for high accuracy and low overall height. 这款测压元件特别适合于高精度和整体高度低的情况。
