您要查找的是不是：
- ball head lock nut 球头锁定螺母
- plain head lock nut 普通头锁止螺母
- Install adjuster nut and lock nut. 安装调节器螺母和防松螺母。
- Lock handle securely by turning lock nut clockwise. 3、顺时针方向拧紧螺帽，可靠的锁好把手。
- To Readjust- Loosen lock nut on the adjusting screw. 重新调节：松开调节螺丝上的锁定螺母。
- To Readjust - Loosen lock nut on the adjusting screw. 重新调节：松开调节螺丝上的锁定螺母。
- Revolving the lock nut 5 anti-clockwise to the suitable position. 逆时针方向旋转锁紧螺母5;使其退到适当位置.
- Disc is fastened securely to disc hanger with a lock nut and cotter pin. 通过一个锁紧螺母和开口销将阀瓣安全紧固在阀瓣支架上。
- Front, side, and rear head locks and chokes. 前面、侧面和后面锁颈和绞技的反击。
- To the player, you always busy helping it with the ball head, cola entered the top down ah! 各位玩家,这个忙你总得帮吧,用头上的皮球,把可乐统统顶下来啊!
- If only one locating ring is required, it should be inserted on the same side as the lock nut. 如果只需一个定位环,此定位环应插入与锁紧螺母相同的一侧。
- My G326 is now using a Cambo ball head, even with 45 camera, it is still strong and good! 相机不够好,只有技术好张就一下当无事;
- The first product we developed and completed based on this theme was the Hard Lock nut. 我们以此为出发点,开始了研究开发,经过不断实验终于研究成功了Hard Lock螺母。
- Small bearings with a bore diameter up to 100 mm can be properly mounted by measuring the lock nut tightening angle. 孔径最大为100毫米的小型轴承可通过测量锁定螺母的紧固角度正确安装。
- To replace diaphragm; loosen lock nut (48) and remove lock washer (46), diaphragm plate (60) and diaphragm (20). 要更换隔膜，先松开锁紧螺母(48)，并拆卸锁紧垫圈(46)，隔膜板(60)和隔膜(20)。
- The built-in ball head allows you to adjust and set its friction so that it balances the weight of your camera without needing locking and unlocking between positions. 嵌入式球形云台可调节和设定阻尼,无需在不同位置间锁定和解锁,即可平衡相机重量。
- Loosen and remove the diaphragm lock nut and lock washer, pressure plate and diaphragm from the valve stem. 松开和拆卸隔膜锁紧螺母和锁紧垫圈，从阀杆上往下压阀盘和隔膜。
- The most compact, full size tripod in the Manfrotto range - the 715B is a four section tripod with an integral ball head with micro "dovetail" quick release plate. 715SHB数码微距三脚架是曼富图系列中最为紧凑的三脚架,它由四节脚管组成,带有球形云台(下面不可辨)和快卸板。
- Arthritic dislocation is the common postoperative complication of total hip arthroplasty and larger ball head could be one of the efficient means to deal with this problem. 摘要关节脱位是全髋关节置换术后常见的并发症，而采用大直径球头是减少术后脱位的可能途径之一。
- Remove spring cage, spring and washer. Remove bottom plug. Grasp upper and lower stem lock nut with wrench and loosen. Clean or replace any damaged or worn parts. 拆卸弹簧笼，弹簧和垫圈。拆卸底部塞。用扳手抓住上部和下部阀杆锁紧螺母并且松开。清洗或更换任何损坏或磨损部件。
