您要查找的是不是：
- First, linear buckling method is adopted to analyze the axial compression member,and then the conclusions are exerted to the struts structure of BSS. 首先采用线性屈曲理论对任意边界的轴心受压杆件进行了屈曲分析,将分析结果运用到张弦结构的撑杆稳定性当中。
- stability of axial compression members 轴压时的工作性能
- ANALYSIS AND COMPARISON OF FLEXURAL-TORSIONAL BUCKLING OF AXIAL COMPRESSION MEMBER 轴心压杆弯扭屈曲分析及对比
- Experimental study on axial compression member made from double steel tubes both in square cross section with concrete-filled sandwich between external and internal tubes 方中空夹层钢管混凝土轴压构件的试验研究
- axial compression member 轴压构件
- The bucking analysis and application of axial compression members with elastic supports 弹性支承上轴心受压构件的屈曲分析及应用
- Keywords aluminium alloy;axial compression members;plate girders;direct strength method;local buckling;distortional buckling;shear buckling;aluminium alloy plate; 铝合金;轴压构件;组合板件;直接强度法;局部屈曲;畸变屈曲;剪切屈曲;铝合金面板;
- The reasonable axial compression, load angle and the ratio of stirrup of special-shaped columns are gained from the contrastive analysis. 通过对比分析，得出了异形柱比较合理的轴压比和加载角度。
- axial compressive member 轴心压杆
- The calculation formulae of critical axial compression for the composite case is given. 给出了复合材料壳体圆筒临界轴压的计算公式。
- And axial force is applied to adobe masonry specimen, which are laid by varies marshaling way, to study their axial compression performance and failure forms. 使用不同的砌筑方法砌筑土坯砌体试件，对试件施加轴心压力，研究砌体轴心受压性能、破坏形态；
- Quasi-static axial compression tests are carried out to study the crushing behaviors of the aluminum foam filled hat sections. 通过试验方法研究了泡沫铝填充帽型结构准静态压溃时的吸能特性。
- After having analyzed the common test methods of working stress briefly, the boring-electrical test method is proposed to test the working stress of RC compression member. 对工程中常用工作应力测试方法进行了简要分析，提出利用钻孔－电测法测试钢筋混凝土受压构件的工作应力。
- Results We got the mechanical property indices of each group on the proneness, aback loll, axial compression, torsion, stress relaxation and creep. 结果得出了各组标本前屈、后伸、轴向压缩、扭转和应力松弛、蠕变力学性能指标。
- To study the behavior of circular tube confined HSC stub columns,6 specimens were tested under cyclic axial compression. 为研究圆钢管约束高强混凝土短柱的轴压力学性能,进行6个短柱试件在循环轴压荷载作用下的试验研究。
- Axial compress is produced by the tension of prestressing beam, which engenders the third moment of column. 预应力筋的张拉会造成梁的轴向压缩,在柱中引起第3弯矩,但在工程设计中通常忽略这一因素影响。
- Conclusion.Horizontal MRI with the patient supine and the legs straightened was comparable to vertical MRI whether axial compression was added or not. 结论：患者仰卧位和下肢伸直位时的水平位MRI比垂直位的轴向压缩程度没有显著性差异。
- Comparative research on method to calculate overall stability of full-web type axially compressed member 钢结构实腹式轴压构件整体稳定性计算方法的比较研究
- The plastic hinge model can also be used for the cantilever tapered castellated beam-columns when the axial compression ratio is below a certain value. 当轴压比较小时，悬臂楔形蜂窝压弯构件可以近似的采用塑性铰模型；当轴压比较大时，利用塑性铰模型分析是不合适的。
- The tested results show that the actual release strains at the edges of the hole agreed well with those of computed by the finite element method, so the boring-electrical test method can be used to test working stress of practical RC compression member. 试验结果表明，孔边实测的释放应变的数值与有限元计算的结果吻合良好，工作应力推定结果与试验结果基本一致，说明该方法可用于实际钢筋混凝土受压构件的工作应力测试。
