您要查找的是不是：
- alloy welding flux 合金助焊剂
- Welding flux greatly improved the efficiency of welding. 焊剂的使用大大提高了焊接的效率。
- High vent effectiveness, non-block or deposit of welding flux in the cell. 通风效率高,焊料不堵孔,不沉积孔口。
- The result indicated that wollastonite had the functions to improve the welding technical performances of this sintered welding flux and mechanical propertiws of melt deposited alloy. 试验结果显示,硅灰石具有改善烧结焊剂的焊接工艺性能和熔敷金属力学性能的作用。
- These alloys weld at different heats. 这些合金可在不同的温度熔接。
- HELI utilized its own R&D and advanced manufacturing technologies to produce carbon steel, stainless steel and hard-facing submerged arc welding flux. 我公司生产的焊剂各种性能优良，焊缝成型美观，脱渣快，抗锈、抗气孔性能好，质量稳定。
- Harbin Xiangying Group Dalai Xiangying Magnesium Alloy Welding Technique CO., LTD. 新型金属哈尔滨翔鹰集团大连翔鹰镁合金焊接技术有限公司。
- Use a blast cleaner or power tool to remove weld flux slag, weld metal spatters, weld flux fume deposits, rust and damaged paint film in welded areas. 通过喷砂或电动工具除去焊渣、飞溅焊烟、锈迹和焊接部损坏的漆膜。
- Real-time sensing and control of weld pool dynamics are important techniques to ensure expected weld quality because there are many uncertain effects especially during aluminum alloy welding process. 由于铝合金焊接过程中存在很多不确定因素,实时的检测和控制熔池动态过程是保证焊接质量的一种重要方法。
- In this article, based on the failure type and failure mechanism of the monel alloy weld joint, the weldability of the material was analyzed, and the weld joint type and weld material were, then, determined. 本文就蒙乃尔合金焊接接头的失效方式、失效机理 ,分析了材料的可焊性 ,并确定其焊材和焊接接头结构型式。
- When laser power density is greater than 12 GW/cm~2,the surface(micro-hardness) of EBW line alters. Mechanical properties of TC4 titanium alloy welding line will be improved by LSP. 当激光冲击的功率密度大于12 GW/cm2时;激光冲击强化处理使电子束焊缝区的表面层硬度明显改变;改善了焊缝区域硬度的分布;有利于提高TC4钛合金焊缝区的机械性能.
- This paper has explained the manufacture principle of Al-flux-cored welding wire, and studied the technical characteristics of Aluminium alloy welding with straight polarity direct current TIG method. 阐述了药芯铝焊丝的制造原理,研究了TIG直流正接焊接铝合金的工艺特点。
- Disposal of Submerged Arc Automatic Welding Flux 埋弧自动焊焊剂的处理
- Hallum, D. L. and Baeslack, W. A., “Nature of Grain Refinement in Titanium Alloy Welds by Microcooler Inoculation,” welding journal, pp. 326-336, September 1990. 高道钢，钛焊接技术，全华科技图书股份有限公司，台北，第二章第3-10
- The issued welding electrodes shall be kept in the carrying case while the welding fluxes shall be used upon issuance. 发放的焊条应存放在保温筒里,焊剂应随领随用。
- This ship is an aluminum alloy welded catamaran passenger vessel, using symmetrical semi-hull, single deck, upper lower cabins and propeller driven. 本船为铝合金焊接双体客船,采用对称片体,单层甲板,设上下客舱,螺旋桨推。
- Metallographic analysis,tension test,fatigue test and SEM analysis were conducted on the TA15 titanium alloy welded joint. 对TA15钛合金板材电子束焊接试样进行了金相分析和静力试验、疲劳试验和扫描电镜(SEM)分析。
- Test results indicate that compound process of laser welding can remarkably improve weld penetration and welding speed,therefore low power laser welder can be used for aluminum alloy welding. 试验结果表明,激光焊复合工艺可以显著提高焊缝熔深和焊接速度,从而实现采用小功率激光焊机实现铝合金激光焊接的目的。
- This paper summarizes the variety and output of submerged arc welding fluxes, and its application status quo to many fields in china is analyzed. 概述了我国埋弧焊焊剂的品种、产量发展及在国内各行业应用的情况,介绍了国外埋弧焊焊剂的生产应用情况,并对我国焊剂的发展提出了一些建议。
- In this paper,the microstructures,phase constituent and micro zone analysis of AZ31B wrought Mg alloy welded joint were investigated by optical microscope,XRD and EPMA. 采用光学显微镜、X射线衍射仪 (XRD)和电子探针 (EPMA)等分析测试手段 ,对变形镁合金AZ31B的TIG焊接头进行了微观组织观察、相组成和微区成分分析试验。
