您要查找的是不是：
- Investigation of Causes Responsible for Wall Thickness Tolerance of Shell as Hot-rolled with Semi-floating Mandrel Mill 半浮动芯棒连轧荒管壁厚不均的原因分析
- Discussion About Wall Thickness Tolerance and Wall Thickness Difference of Bushing 小议衬套壁厚公差与壁厚差
- Wall thickness tolerance 壁厚精度
- Range Min and Max.-OD with wall thickness. 范围分钟和最大Od以壁厚度。
- Tolerance on outer diameter and wall thickness should be observed,but for the following two circum stances,shorter axis should not be less than 95% of nominal diameter. 管材的不圆和壁厚不匀，应不超出外径的壁厚允许偏差，但属下列两种情况之一者，其短轴尺寸应不小于公称外径的95%25。
- Thickness tolerance is an important parameter in radiographic testing of thickness changed object. 厚度宽容度是变截面工件射线检测的重要参数。
- The paper analyzed the thickness difference in typical objects,and thickness tolerance required for different sensitivity classes. 本文分析了典型工件的厚度差,以及不同灵敏度级别的厚度宽容度。
- The backing of bearings with greater wall thickness is not copper-plated. 轴承壁较厚的轴承,其背衬不镀铜。
- APACO processes Hardboard, MDF or Chipboard up to a wall thickness of 18mm. 橱柜/壁柜/橱柜门板/人造石厨房台面加工制作.
- The forecasted wall thickness was conformed to the experimental result. 预测的壁厚和实验结果吻合得很好。
- In order to decrease the thickness tolerance and improve the surface quality for bamboo plywood form in our country bamboo-wood composite technology and secondary veneer overlaying were studied. 针对目前国内竹胶合板建筑模板普遍存在厚度公差大、表面质量差等严重影响产品质量的问题,进行了竹木复合和二次覆面工艺的探索。
- End connection including wall thickness of connecting pipe if weld end and any special flange facings or finishes. 连接方式,如果是焊接端口和任何法兰面或表面,则包括连接管道的壁厚。
- What is the foundry's checking frequency for control of core shift and wall thickness? 工厂检验芯偏移以及壁厚的频率?
- The tube deformation characteristics on ASSEL mill are deformation concentrating at shoulder and wall thickness in rolling zone increasing. ASSEL轧管机具有台肩集中变形、碾轧段壁厚增厚等特点。
- The wall thickness of a 1-litre bottle preform is 3mm. The cooling time is 10.8s. 1公升的矿泉水瓶瓶坯壁厚3mm，冷却时间便占10.;8秒。
- The wall thickness of a 5-gallon bottle preform is 8mm. The cooling time is 76.8s. 5加仑瓶瓶坯壁厚8mm，冷却时间是76.;8秒。
- When chilled water is used to cool the mould, cycle time is related to wall thickness as follows. 在冰水冷却的条件下，冷却时间与壁厚有以下的关系。
- Thickness Tolerance of Hot-rolled sheet 热轧钢片厚度公差
- Control of Thickness Tolerance of Zinc Slug Coils 锌饼卷坯厚度精度的控制
- The aorta wall thickness (AWT) was measured wiht B-mode echocardiography in 128 patients with primary hypertension. B型超声心动图下测量了128例高血压病患者主动脉壁厚度（AWT），同时检测了血脂指标。
