您要查找的是不是：
- Research results show that with application of Mucell,the 10% raw material can be saved,the injection pressure is decreased by 36.7%,the clamp forc... 研究结果表明:采用微孔发泡注射成型工艺可以节省原材料10%25;注射压力降低了36.;7%25;锁模力降低了60
- Twoprocess mode can be ed, single or continuous. The clamping force of hold down device will in crease when cutting force increases. 两种使用模式给客户选购，单次或连续。另压片力会随着剪切力增加而自动调节。
- Its paper clamp presses tightly against the material to be cut by means of a high quality strong pull spring assembly and the clamping force can be adjusted readily. 压纸器是由优质强力拉簧组使其牢牢地压紧裁切物,压力大小调整方便。
- Injection molding machines, which are generally horizontal, are rated according to the capacity of the mold and the clamping force on the molds, which in most machines is a few hundred tons. 注射成型机器，一般是水平的（卧式的），它是依据铸型的容量（注射量）和铸型上的箝位力（锁模力）来额定的（进行标定），大多数机器（注射机）的额定量为（锁模力有）几百吨。
- By setting strainometers on mold, the authors adopt strain principl to detect the clamping force of injection machine and realize acquisition, display and processing of data by computer. 本文采用应变原理，通过在假模上放置应变片来检测注塑机锁模力，并由计算机实现数据采集、显示和处理等。
- The clamps should be stable, the clamping force should be in normal direction to the support surface. 5夹紧器要稳定可靠，夹紧方向按定位面法线方向。
- Deciding the overall concept of jigs, which include the method of machining, method of fixing and analysis of fixing error, method of clamping and the calculation of the clamping forces of cutting . 确定夹具总体方案，包括加工的方法、定位方案和定位误差的分析、夹紧方案、切削夹紧力的计算。
- Check the clamping force in relation to the part geometry 检查锁模力与制品几何关系
- The Computation of the Elongation of Thin-Walled Workpiece From the Clamping Force 薄壁工件在夹紧力作用下变形量的计算
- Can auto-induction the can size and weight, auto-adjust the clamping force, and auto-unclamp when finished; 自动感受物料容器尺寸及重量大小，自动调整夹紧力大小，运行完毕自动松开；
- 5. Can auto-induction the can size and weight, auto-adjust the clamping force, and auto-unclamp when finished; 自动感受物料容器尺寸及重量大小，自动调整夹紧力大小，运行完毕自动松开；
- Sturdily mount the clamping device of machine. 研磨机夹持必须安装牢固。
- Clamping force equalization: same force to two workpieces in different size. 自动补偿机构：不同大小工件，可在同时夹紧，且夹持力相同。
- The clamping unit is totally enclosed to contain dry air. 锁模装置还要密封，保存着干燥的空气。
- The clamping force 夹紧力
- The wood is held in position by a clamp. 木头用钳夹固定住了。
- Slide the clamp up and center over the largest barb. 将夹子滑上并将最大的倒钩处于中心位置。
- Size and grade specific cap bolts offer superior clamping force between the cap and base. 座罩螺栓有不同的尺寸和等级,在座罩和基础之间形成理想的夹持力。
- In using an injection moulding machine, it is best to use the minimal but adequate clamping force F. 使用注射成型机，最好使用最小同时充足的锁模力F。
- The two deices do clamping force measurement/control and caity pressure switchoer to holding pressure. 这两个装置就是锁紧力量测/控制装置和（射出）转保压的模腔压力转化装置。
