您要查找的是不是：
- Calculation of braided shielding cable responses in radiation and pulsed current injection environments 辐照和电流注入下电缆耦合响应的计算
- Pulsed current injection 脉冲电流注入
- A pulsed current solenoid wiggler[J]. 引用该论文 严祖祺.
- Hence the coil can be still stable against a pulsed current shock. 因此，在遭遇大电流冲击时，线圈仍有可能保持稳定。
- So in the solution studied the HSI anode could be used in pulsed current cathodic protction system. 因此，在所研究的介质中高硅铸铁阳机可以用于方波脉冲电流阴极保护。
- A three-dimensional numerical analysis model of fluid flow and heat transfer in pulsed current TIG weld pool is developed. 对运动电弧作用下脉冲TIG焊接熔池流场与热场动态变化过程建立了三维数学模型。
- There are two kinds of current injection techniques: bulk current injection (BCI) and direct Current Injection (DCI). 电流注入技术主要有两种:大电流注入(BCI)和直接电流注入(DCI)。
- This paper introduces the study of Direct Current Injection(DCI)technique used in EMC-testing for missile. 介绍了直接电流注入技术在导弹EMC性能测试中的具体应用。
- Special pulse current technology solvesthis issue well. 采用特别的脉冲电流技术能很好地解决这个问题。
- It can provide large pulse current to load for discharge. 它可为负载提供大电流脉冲放电。
- It possesses outputs of AC, DC, AC pulse and DC pulse current. 它可以输出矩形波交流、直流、交流脉冲和直流脉冲四种电流。
- The paper deals w ith a current inject ion method by w h ich the po sit ion angles of salient po les can be est imated.A design of the con2 t ro l of senso rless BLDC based on DSP is offered. 文中介绍了一种新颖的以电流注入方式求得凸极转子位置的检测方法,并给出了基于DSP的无刷直流电机无位置传感器的控制方案及其软硬件设计。
- The adiabatic heating model of exploding wires is used to simulate their blasting characters on strong pulsed current, andto gain the influence trends fo exploding wire numbers to their hlasting chacters. 用电爆丝绝热加热模型数值模拟了电爆丝在冲击大电流作用下的电爆炸特性，电爆丝根数对电爆炸特性的影响。
- The stepping motor of wire feeding is controlled by a pulsed current,which is output from the HSO.1 port of a 80C196KC single-chip microcomputer(SCM) and thus oscillating feeding of wire is realized. 通过改变焊接回路的电压反馈比例获得脉冲电压;利用给定电压调节短路电流;用80C196KC单片机的HSO.;1口产生脉冲波形控制送丝步进电机;形成脉动送丝方式。
- The stepping motor of wire feeding is controlled by a pulsed current, which is output from the HSO.1 port of a 80C196KC single-chip microcomputer(SCM) and thus oscillating feeding of wire is realized. 通过改变焊接回路的电压反馈比例获得脉冲电压，利用给定电压调节短路电流，用80C196KC单片机的HSO.;1口产生脉冲波形控制送丝步进电机，形成脉动送丝方式。
- A low? cyanide bright gold plating process with pulse current was developed. 开发出一种低氰脉冲光亮镀金工艺。
- The electrochemical performance of High Silicon-Iron Anodes Exerted by Square Wave Pulsed Currents (SWPCs) was studied by electrochemical. 摘要采用电化学方法和阳极消耗率评价法研究了高硅铸铁阳极在方波脉冲电流作用下的电化学性能。
- Based on clustering FSVM and current injection method,a new method using two steps for single-phase grounding fault location of distribution feeders in networks with ungrounded neutral is proposed. 提出小电流接地系统实现单相接地故障定位的新方法。该方法应用基于聚类的FSVM和电流注入法分两步实现故障定位。
- Either 1 mA current is injected from S layer to F layer (+I_(inj)) or from F layer to S layer (-I_(inj)), the normal resistance is lower than that without current injection. 在F/S双层结构中通入1mA的注入电流,无论电流从S层流入F层(+Iinj),或者电流从F层流入S层(-Iinj),正常电阻均比未加注入电流时的电阻低;
