您要查找的是不是：
- Pressure Induced Flow Moulding 压力诱导流动成型
- Pressure Induced Flow Processing 压力诱导流动成型
- Study on Mechanical Properties and Micromorphology of PP Prepared by Pressure Induced Flow Processing 压力诱导流动成型PP的微观结构与力学性能研究
- This induced flow produces a positive moment that increases with wing lift or a. 这一诱导气流产生正的力矩，该力矩随升力或迎角a的增加而增加。
- Pressure Induced Disruption of Cytoskeleton and the Protein Synthesizing Machinery. 压力引起的细胞骨架、及蛋白质综合体系的破坏。
- The test results show that the rotor induced flow changes the warship airwake and the influence of the rotor can be reduced by opening the hangar door. 结果表明，旋翼诱导速度改变了舰船尾流分布，打开机库门可减弱旋翼的影响。
- However, this is not sufficient to overcome or prevent the marked spasm and increase in biliary duct pressure induced by opiods. 然而，这不足以对抗或防止阿片类引起的明显痉挛和胆道内压升高。
- Polyglycol (PEG)/poly (lactic acid) (PLA) blend was processed by means of pressure-induced flow moulding (PIF).The effects of PIF on the structure and property of the blend were studied. 摘要采用压力诱导流动成型(PIF)对聚乳酸／聚乙二醇(PLA/PEG)共混物进行加工，研究了PIF对PLA/PEG共混材料的结构和性能影响。
- Main service:Gas foam Acidification,flowback,well cleaning,sand washing,broken down,induced flow;Foam profile control,oil displacement;gas foam less balance drilling. 主要服务项目：气体泡沫酸化、返排、洗井、冲砂、解堵、诱喷；泡沫调剂、驱油；气体泡沫欠平衡钻井。
- A detailed linear thermoviscoelastic model was developed to calculate thermally and pressure induced residual stress and shrinkage in amorphous plastic parts. 基于线性黏弹性模型模拟计算了注塑成型过程中由温度和压力引起的残余应力和收缩。
- Pressure induced amorphous transition of LiB 3O 5(LBO) has been investigated by using in situ high pressure X ray powder diffraction and energy dispersive X ray diffraction with synchrotron radiation at the pressure up to 45 1GPa. 采用X射线粉末衍射和同步辐射能散X射线衍射技术，对LiB3O5（LBO）晶体进行了压致非晶化相变的研究，压力达45.;1GPa。
- The excessive pore water pressure induced by excavation should be determined by the undrained triaxial compression test according to the stress path of the soil in and out of foundation pit. 对于基坑开挖卸载所引起的超静水压力，应根据坑内外土体的应力路径做三轴不排水剪试验确定。
- Keywords PLA;Polyglycol;Pressure-induced Flow Moulding;Toughening; 聚乳酸;聚乙二醇;压力诱导流动成型;增韧;
- Woofer driver: 8 ", acustically transparent high flow moulded aluminium basket, rubber suspension, treated non pressed paper cone. 低音驱动器：8"，透声高流动性铝铸盆架，橡胶盆架，高温处理松压纸盆。
- Wang, K.H. and Yang, J.C., “Three-dimensional modeling of flood induced flows and sediment concentration in Shihmen Reservoir in Taiwan”, FLUCOME, Tallahassee, Florida, USA, 2007. 陈建华、谢德勇、杨锦钏，“弯道超临界流交波现象模拟之分析”，第十六届水利工程研讨会，民国96年8月。
- It showed that deformation twins had formed in 2Cr17Mn15Ni2N and 304L targets, despite the peak pressures induced by LSP were no more than one third and half of the critical stress for twinning of corresponding targets. 结果表明,激光诱导的峰压不到2Cr17Mn15Ni2N和304L不锈钢靶材孪生应力的1/3和1/2时即有形变孪晶形成;
- The results show that because of the function of the velocity item in Reynolds equation, the pressures induced by the corresponding roughnesses make the rough surface flattened in both line and point contacts, especially under heavy loads. 从计算结果可以看出,由于Reynolds方程中速度项的作用,在表面对应粗糙的位置处引起了压力变化,从而因其产生的弹性变形使粗糙变得平滑。
- The beer comes out of the barrel under pressure. 啤酒受到压力从桶中流出。
- Our pressure vessel is licensed product. 我厂生产的压力容器是授权生产产品。
- Loss of pressure had not registered on the dials. 刻度盘未记录压力下降。
