您要查找的是不是：
- Preventive and Forming Mechanism of Plate Surface Defect "Black Strip" 板材表面"黑条子"缺陷的形成机理和预防方法
- Plate Surface Defect 钢板表面缺陷
- Antistatic device,keep any dust from plate surface. 防静电装置，防止任何微细灰尘沾附膜面，确保膜面洁净。
- A surface defect in paper. Alternative terms: blisters; foam marks. 中义纸张的表面缺陷，参考字：气泡痕迹。
- Surface defect in cold rolled galvanization plate in Handan Iron and Steel Limited Group has been introduced,meanwhile the solution process has been discussed. 介绍邯钢冷轧热镀锌线在生产中所遇到的一些表面缺陷,及对解决过程中所遇到的一些问题进行探讨。
- The remote bending stress at the plate surface was measured. 板表面处的远场弯曲应力已被测出。
- Surface defect and macrostructure of high carbon steel billet were analyzed. 介绍了铸坯相关表面缺陷及低倍组织,提出了质量控制措施及方案。
- A kind of washboard-like crack on steel plate surface is introduced. 摘要文章介绍钢板表面产生的一种搓板状裂纹。
- Exterior measurement includes specification and size, surface defect, and sewing requirement. 外观质量包括规格尺寸及公差、表面疵点、缝制要求。
- Zinc content in the alloy above 0. 05% consistently resulted in an unacceptable surface defect as galvanizing. 锌含量低于0．05%25时，型材一般不发生雪花状腐蚀。
- Surface defect detection is important to ensure the utility,integrality,and security of the products. 产品表面缺损检测对保证产品的使用性能、完整性和安全性具有重要意义。
- The article describes the problem of the toughened glass' surface defect and the method of prevention and solution. 针对钢化玻璃表面质量存在的变形点缺陷,采取相对应措施预防和解决。
- Small and superficial occlusal surface defect ,proximal and labial surface defect uninvolved incisal angle . 2 .;合面缺损范围小而且表浅，前牙邻、唇面缺损未涉及切角者，不宜用嵌体修复。
- Equipped with brute mighty dust absorption system, Which makes the plate surface clear, and circumstance saniation. 配备吸尘设备,以保持锯版工作面清晰和环境卫生。
- The lampstand uses the high quality cold rolled plate surface spray coating to become. 产品说明:灯架采用优质冷轧板表面喷涂而成。
- Using flexible interpolator pad is an important way to suppress the part surface defect in stretch-farming process on multi-paint tool. 摘要采用柔性垫层是抑制和消除多点模拉形过程中零件表面缺陷的重要措施。
- Resin rubber nylon photoptic edits, casting in zinc plate surface, similar to self adhesive resin trademark used above. 树脂版以尼龙感光胶为主，浇铸在锌版表面，类似于不干胶商标上面使用的树脂版。
- This paper analyzes the reason that caused the surface defect of billet produced by EAF Steelmaking plant of Nanjing Iron and Steel Co.Ltd. 分析了南(京)钢电炉厂小方坯表面质量问题及产生的原因,涉及结晶器振动参数、保护渣等。
- The surface roughness Ra was about 3 nm.Therefore, it is quite smooth plate surface of thin films. 表面平均中心粗糙度约在3奈米左右，所形成之薄膜具有相当平整的表面。
- Objective: To provide anatomic basis for repairing the knee joint surface defect with the pedicled patella translocation. 摘要目的：为带血管蒂髌骨移位修复股骨髁和胫骨髁关节面缺损提供解剖学基础。
