您要查找的是不是：
- Open Test Assembly 公开测试组件
- Vibration Open Test Assembly 振动开放试验/测试装置
- Open test cock No. 4 and flush test cocks Nos. 1, 2 and 3 on reduced pressure assembly then close test cock No. 4. 开启测试旋塞4号，冲洗减压总成上的测试旋塞1号，2号和3号，然后关闭测试旋塞4号。
- B. Open test cock No. 4 and flush test cocks Nos. 1, 2 and 3 on reduced pressure assembly then close test cock No. 4. 开启测试旋塞4号并冲洗减压总成上的测试旋塞1号，2号和3号，然后关闭测试旋塞4号。
- After shutoff valves are closed, open test cock #2, #3 to relieve pressure within the backflow assembly. 在关闭了关闭阀后，开启测试旋塞2号，3号和4号，释放回流阀总成的压力。
- After shutoff valves are closed, open test cock #2, #3 & #4 to relieve pressure within the backflow assembly. 在关闭阀关闭后，开启测试旋塞2号，3号和4号，释放防回流阀总成内部压力。
- After shutoff valves are closed, open test cock #2, #3 and #4 to relieve pressure within the backflow assembly. 在关闭了关闭阀后，开启测试旋塞2号，3号和4号，释放回流阀总成的压力。
- Close shutoff valve No. 2 then shut off valve No. 1 on test assembly. 关闭2号关闭阀,然后关闭测试总成上的1号阀门。
- The test assembly allowed me to check that it ran smoothly without a motor. 测试组合件允许我检查它能够在没有电机的情况下顺利运行。
- Tighten bypass hose at test cock No.1, open test cock No.1. 紧固测试旋塞1号上的旁路软管，开启测试旋塞1号。
- Tighten bypass hose at test cock No. 1, open test cock No. 1. 紧固测试旋塞1号上的旁路软管，开启测试旋塞1号。
- Open test cock No. 1 and bleed valve "A" on top of test kit. 开启测试旋塞1号和检测组件顶部上的排气阀“A”。
- Close needle valve "A" high side (red) and open test cock No. 2. 关闭针形阀“A”高端（红），并开启测试旋塞2号。
- Open test cocks to drain in cold climates if only operated seasonally. 如果仅仅是季节性运行,则在寒冷环境下开启测试旋塞。
- In this case, the test generation procedure creates a private accessor, which enables the test assembly to access those types, both internal and private. 在这种情况下,测试生成过程将创建一个专用访问器,使测试程序集能够访问这些类型。
- The output of this procedure is promising with above 98% accuracy in open test. 开放测试结果表明分词精确率可达 98%25以上
- Open test cock No. 2 and needle valve "A" high side (red) on test kit. 开启测试旋塞2号和检测组件上的针形阀“A”高端（红）。
- Open test cock2. Installing EZ-TC adaptor opens test cock2. 开启测试旋塞2号。安装EZ-TC适配器，开启测试旋塞2号。
- Open test cock3. Installing EZ-TC adaptor fitting opens test cock3. 开启测试旋塞3号。安装EZ-TC适配器连接件，开启测试旋塞3号。
- A Boolean value that determines whether each unit test assembly will run in a separate application domain when the load test contains unit tests. 这是一个布尔值,它决定当负载测试包含单元测试时,是否在单独的应用程序域中运行每个单元测试程序集。
