您要查找的是不是：
- Lock washer internal teeth LT 内齿锁紧垫圈
- Serrated lock washers internal teeth 内锯齿垫圈
- internal tooth lock washer 内齿锁紧垫圈
- Early lock washer on left, as used on the 600 series. 左边是早期的固定垫圈，使用在600系列上。
- Serrated lock washer external teeth for assembly 组合件用外锯齿锁紧垫圈
- To replace diaphragm; loosen lock nut (48) and remove lock washer (46), diaphragm plate (60) and diaphragm (20). 要更换隔膜，先松开锁紧螺母(48)，并拆卸锁紧垫圈(46)，隔膜板(60)和隔膜(20)。
- Hold stem (27) on wrench flats and remove nut (51), lock washer (46), diaphragm plate (60) and diaphragm. 在扳手的平面上握住阀杆(27)并拆卸螺母(51)，锁紧垫圈(46)，隔膜板(60)和隔膜。
- round elastic washer with internal tooth 内齿弹性圆垫圈
- Loosen and remove the diaphragm lock nut and lock washer, pressure plate and diaphragm from the valve stem. 松开和拆卸隔膜锁紧螺母和锁紧垫圈，从阀杆上往下压阀盘和隔膜。
- Plain washers, spring washers, internal tooth washer, external tooth washer, other abnormity washers, circlip for shaft (external), circlip for hole (internal), split washer. 平垫圈、弹簧垫圈、内齿垫圈、外齿垫圈、内锯齿垫圈、外锯齿垫圈、其他异形垫圈；轴用（外卡）弹性挡圈、孔用（内卡）弹性挡圈、开口挡圈。
- Disassemble module. Use wrench to loosen stem nut and remove lock washer and diaphragm plate. Remove yoke by loosening disc holder using a screw driver. 拆卸模块。使用扳手松开阀杆螺母，并且拆卸锁紧垫圈和隔膜板。采用螺丝刀，通过松开阀瓣支架来拆卸轭架。
- Swing mechanism comprises an axial piston motor with cushion valve and a planetary gcear reducer.Fully sealed singlerow ball swing ring with monobloc internal teeth,grease bathed. 带有缓冲阀的轴向柱塞马达与行星齿轮减速机组成的回转机构，单列球型整体内齿式全密封回转支承，油脂润滑。
- Smaller sizes use a lock nut with a locking washer (a), larger sizes use a nut with locking clip (b). 小尺寸轴承使用带锁紧垫圈的锁紧螺母(a)大尺寸的轴承使用带锁紧卡箍的锁紧螺母(b)。
- Hexagon head bolt and serrated lock washer external teeth assemblies 六角头螺栓和外锯齿锁紧垫圈组合件
- Swing mechanism comprises an axial piston motor with cushion valve and a planetary gcear reducer.Fully sealed singlerow ball swing ring with monobloc internal teeth, grease bathed. 带有缓冲阀的轴向柱塞马达与行星齿轮减速机组成的回转机构,单列球型整体内齿式全密封回转支承,油脂润滑。
- Single coil spring lock washer for assembly 组合件用弹簧垫圈
- lock washer with tongue at outside 外舌止动垫圈
- Hangzhou Zhengda Spring Lock Washer Co., Ltd 杭州正大弹簧垫圈有限公司
- Serrated lock washers exteral teeth 外锯齿锁紧垫圈
- front wheel bearing nut lock washer 前轮毂轴承螺帽锁紧垫圈
