您要查找的是不是：
- Injection Filling Process 注射充模过程
- The mold flow analysis utilizes the computer to simulate dynamic filling process about the injection mold. 模流分析技术是利用计算机对注塑件动态填充过程进行模拟。
- The molding filling process is a very important phase in RTM. 树脂充模是RTM工艺成型过程中的重要一环。
- Chen, S.C., Y. C. Chen And N. T. Cheng, "Simulation of Injection Compression Mold Filling Process", Int. comm. Heat Mass Transfer.Vol.25, No.7,pp. 907-917, 1998. 陈裕承;”短射压缩成型之基本探讨与应用”;台湾大学机械工程研究所硕士论文(1996).
- You must know how to stop the cylinder filling process in case of an emergency. 你必须知道在紧急情况下,如何停止气瓶的充装。
- The simulation result is in good agreement to the actual filling process. 实践证明 ,模拟结果同实际浇铸过程比较吻合
- The results provide scientific basis for the safety assessment of the filling process in the inverted siphons. 计算结果可为大型倒虹吸管充水过程的安全评估提供科学依据。
- The pressurizing and filling process is preceded by triple pre-evacuation and double CO2 purging. 在加压和灌装过程之前三重前撤离和双重二氧化碳净化。
- Evidently, a CO2 leak occurred during the fill process, leaving both persons trapped in the storage room. 很显然，充装的过程中出现了CO2泄漏，使得他们都被截在了储藏室内。
- The mathematical model that describes the PIM filling process is created, and the formula for calculating the flow conductance is deduced. 推导了喂料熔体流导率的计算公式,得出压力场的控制方程是一非线性椭圆偏微分方程。
- It is proved that the designed gating, overflow well and air vent are reasonable, which can stabilize the whole filling process. 经分析验证证明：所设计的浇道及溢流槽、排气槽合理，整个充填过程平稳。
- Media fill is a method of evaluating sterility assure level of an aseptic fill process using microbial culture medium. 介质灌装是一项采用微生物培养介质评价无菌灌装过程无菌保证水平的方法。
- The mould filling process of rheo-die-casting of semi-solid magnesium alloy has been analyzed with die-casting experiments. 通过压铸实验分析了镁合金半固态流变压铸、液态压铸充型流动过程。
- Objective To review our experience with the application of polyacylamide hydrogel (PaH) as an injectable filling material in augmentation mammoplasty. 目的总结聚丙烯酰胺水凝胶注射隆乳的临床经验。
- Pre-dosing of the filling quantity in a dosing tank allows for high filling accuracy and high speeds, as the filling process is not affected by product foaming or bubbling. 由于用配料罐对灌装量进行预配料,可以达到很高的灌装精度,并由于灌装过程与气泡灵敏度或产品起泡独立进行还可以取得高的效率。
- A practical software suitable for simulation of filling using micrcomputer was also developed,which could numerically simulate filling process in evaporative patte... 同时开发了适用于微机的充填过程模拟软件，准确、合理地对气化模充填过程进行计算机模拟。
- The effect of coating layer on the molten metal filling process in Evaporative Pattern Casting (EPC) has been studied by means of numberical simulation. 采用数值模拟技术研究了涂料对消失模铸造金属液充型过程的影响。
- CUSUM control chart is used to solve the problem and to improve machine calibration, which results in high quality and low cost in fluorine filling process. 本文采用累积和控制图(CUSUM)来控制充氟量偏差的变化，改进了充氟偏差调整方式，在保证质量的同时降低了生产成本。
- Based on the quasi-steady and quasi-static hypothesis, a differential equation mode for the filling process of large multi-segment inverted siphon is derived. 摘要基于准恒定准静态的假设，推导了大型多段倒虹吸管充水过程的微分方程模型。
- In lost foam casting (LFC) ,the foam pattern is the key qualification, and the beads filling process is quite crucial to ensure the high quality of the foam pattern. 泡沫模样是消失模铸造成败关键,而泡沫珠粒的充填是获得优质泡沫模样的关键工序之一。
