您要查找的是不是：
- GPC control algorithm 广义预测控制算法
- The algorithm presented in the paper is on the basis of generalized predictive control theory, singlevariable GPC and DMC mixed control algorithm. 本文在广义预测控制原理及单变量广义预测与动态矩阵混合控制算法的基础上，提出了多变量广义预测与动态矩阵混合控制算法。
- The GPC structure scheme based on ANN for the nonlinear system is designed.And the control principle and control algorithm are studied, based on the high nonlinear mapping of ANN. 基于ANN高度非线性映射等特性，运用数字仿真方法，对所设计的控制结构方案进行仿真研究。
- Correct control algorithm is the key of network congestion control. 因此,正确的控制算法是网络拥塞控制的关键。
- The control algorithm uses the increase type PID control algorithm. 系统实时性和控制精度较高。
- So the adaptive character of the control algorithm has been enhanced. 将该算法应用到电控气动离合器操纵系统中并进行实验。
- An intelligence PID control algorithm based on the expert system was discussed. 讨论了一种基于专家知识的智能PID控制算法。
- Stability condition of the proportional control algorithm is given for a fixed target. 针对固定目标，文中给出了比例控制算法的稳定性条件。
- The system is composted of a high accuracy thermocouple and a 8031 single chip computer while adaptive PID control algorithm is employed. 该系统由一个高精度的热电偶和8031单片机组成，采用自适应PID控制算法。
- A new parameters adaptive PID control algorithm is put forward on the basis of Cohen Coon assignment formula. 在Cohe Coon整定公式的基础上 ;提出了一种参数自适应PID控制算法 .
- First, the TCP theory and the key technology of TCP congestion control algorithm are researched in the thesis. 首先,对Internet中传输控制协议的原理以及TCP拥塞控制算法中的关键技术进行了深入探讨和研究。
- First, the jitter control algorithm aims at smoothing the jitter variance with low queueing delay latency. 首先，延迟变异控制机制目标在低延迟代价条件下，减缓延迟变异。
- On this basis, the basic model of main-shaft-less concave printer and ADRC are combined to get a new control algorithm. 在此基础上又将推导出的无主轴凹印机粗基本模型与AD-RC相结合，得出新的控制算法。
- For to evaluate the various control algorithm, Spencer, et al. present a AMD benchmark model. 为了能对各种算法有一个公认的评价标准，美国Notre Dame大学Spencer研究组通过对主动质量驱动(AMD)控制的三层框架模型实验的数据分析，建立了AMD控制Benchmark模型。
- Fuzzy control algorithm is programmed by Borland C++, control of inverted pendulum hardware system is realized. 利用Borland C++编写模糊控制算法程序，实现了倒立摆实物系统控制。
- It is important to develop the ABS ECU, study the control algorithm of ABS, and validate control logic of existing ECU. 它对于ABS ECU的开发、ABS逻辑的研究、验证ECU控制策略的合理性及实用性都是很有效的工具。
- positive control group had higher MST, Ep, TFL than GPC control group; 阳性对照组较GPC对照组MST、EP、TFL升高，有显著性差异。
- Analying the influence of output transform to NNC control algorithm in neural-PID control. 对神经PID控制中,输出转换成过程对NNC控制算法的影响进行了讨论,使神经PID控制在各种情况下得以正确应用。
- Optimized control models under PEM SPM EDM control algorithms are obtained. 给出了系统在PEM、SPM、EDM三种控制策略下的优化控制模型。
- This paper presents a model predictive control algorithm for affine nonlinear systems. 摘要本文提出一个用于仿射非线性系统的模型预测控制算法。
