您要查找的是不是：
- The rare earth additive has the tremendous influence to the compress yield strength of foam aluminum alloy, the best rare earth content is 0.40% (quality score). 摘要稀土添加剂对泡沫铝合金的抗压屈服强度有较大的影响，最佳的稀土添加量为0.;40%25（质量分数）。
- Compress yield strength 抗压屈服强度
- The application of BP model in predicting porosity and compressive yield strength of porous NiTi alloy BP模型在预测多孔NiTi合金孔隙度和屈服强度上的应用
- Compression Yield Strength 压缩屈服强度
- compressive yield strength 抗压屈服强度
- Desirable properties for forming include low yield strength and high ductility. 令人满意的成形特性包含了低降伏应力和高延展性。
- With the increase of SiC foam aperture, the compressive strength, elastic modul and yield strength of the composites increase, but the ratio of compress decreases. 当筋具有双层结构时, 复合材料的强度最低；
- Oxygen precipitates (useful for gettering) can reduce the yield strength (critical shear stress) up to fivefole. 氧沉淀(可用作吸杂)会使屈服强度(临界剪应力)降低为五分之一。
- The welder shall be capable of welding (full hard cold-rolled) steel with yield strength of up to 85Kg/mm2. 焊机应能焊(冷轧全硬)其屈服强度大于85Kg/mm2的钢带。
- The V-N microalloy steel with yield strength of 550 MPa is produced by EAF-CSP route. 目前,在EAF-CSP流程中通过V-N微合金化技术可成功生产屈服强度为550 MPa的高强度低合金钢。
- The result show that the yield strength of the bars drop apparently and the tensile strength rise a little. 结果表明,自然时效后钢筋的屈服强度有较大幅度下降,抗拉强度有小幅度的上升。
- Oxgen precipitates (useful for gettering) can reduce the yield strength (critical shear stress) up to fivefole. 氧沉淀（可用作吸杂）会使屈服强度（临界剪应力）降低为五分之一。
- Change of molecular magnetic moment of motherliquor and shear yield strength are studied in magnetorheological fluid. 对磁流变液中母液分子在磁场作用下磁矩的变化以及由此引起的剪切屈服强度的变化进行了研究.
- Torque values listed are typical or alloy steel bolts (approximately 100,000 psi yield strength) used with carbon or intermediate alloy steel valves. 所列的扭矩值是标准值或适用于合金钢螺栓(屈服强度大约为100,000 psi),配置在碳钢或中间合金钢阀门上。
- Relationship between yield strength and near-neutral pH stress corrosion cracking resistance of pipeline steels-an effect of microstructure. 管道钢的屈服强度和抗近中性pH应力腐蚀开裂间的关系-显微结构的影响。
- Tensile and yield strength are determined by pulling a standardized machined sample in an tensile testing machine until the sample breaks. 抗拉强度和屈服强度的测定是在拉力试验机中将一个加工好的标准试样进行拉伸直至试样断裂。
- The output parameters of the model are three mechanical properties namely ultimate tensile strength (UTS), yield strength (YS) and elongation (ELO). 模型的输出为三个力学性能指标,即抗拉强度、屈服强度和延伸率。
- We will never yield to invaders. 我们绝不会向侵略者屈服。
- The results showed that the Vicat softening temperature and the tensile yield strength were improved with the increase of CPVC content. 结果表明,共混材料的维卡软化温度和拉伸屈服强度随CPVC用量的增加而增加;
- API regulates that the yield strength of flatten specimen from pipe body is used to characterized the yield strength of oil pipeline body. 根据美国石油学会API标准规定,采用管体取样压平试样的屈服强度表征输油管体屈服强度。
