您要查找的是不是：
- Cold Work Hardening Plate 冷作硬化板
- Keywords cold rolling;cold work hardening;hadfield steel;abrasive wear; 冷轧;形变强化;高锰钢;磨料磨损;
- Experiment and Study on Cold Work Hardening to Increase the Permanence Limit of Mechanism 表面硬化处理对提高构件持久极限的试验研究
- Effect of cold work hardening on stress corrosion cracking of stainless steels in primary water of pressurized water reactors 冷加工硬化对压水堆一回路水中不锈钢应力腐蚀裂纹的影响
- cold work hardening 冷加工硬化
- The yield strength of JCOE welded pipe was different from the mother steel plate because of the influence of Bauschinger effect and work hardening. 摘要由于包辛格效应和加工硬化的影响，JCOE制管后相对所采用钢板管体屈服强度会发生变化。
- Type: High Strength Cold Work Tool Steels. 类型:高强度冷作工具钢。
- Its elongation of cold rolling can reach 6100% without any cracks in the edges.The single crystal copper exhibits more serious work hardening in wiredrawing.The plasticity and ... 冷拉拔加工后单晶铜表现出更大的加工硬化现象,但采用合理的退火工艺可使其加工硬化得到缓解。
- The results show that the work hardening rate of pure tantalum is low. 研究结果表明:纯钽的宏观加工硬化速率比较低。
- cold working hardening 冷加工硬化
- The results show that the effects of work hardening by strain-induced martensite transformation and cast pore defects are the main reasons leading to strip broken of the steels during cold rolling. 结果表明,形变诱发马氏体组织所加剧的加工硬化与冶炼时所产生的气孔缺陷的共同作用是冷轧断带的原因。
- ER5 is a cold work die steel with high wear resistance and toughness. ER5是一种高耐磨冷作模具钢。
- MISO option uses the von Mises yield criteria coupled with an isotropic work hardening assumption. 帮助中的小应变分析和大应变分析具体是指什么情况?
- HAYNES HR120 alloy cutting performance is bad and isvery sensitive to the work hardening. HAYNESHR120合金切削性能差,对加工硬化很敏感。
- DP steel has better work hardening ability while TRIP steel has better bake hardening ability. DP钢拥有更加优良的加工硬化能力,TRIP钢则具有较为理想的烘烤硬化能力。
- Pads that bottom out will have hardened plates. 最底的垫板应该热处理。
- The simulation results suggest that Bauschinger effect and work hardening etc are validated in the model. 模拟结果表明,弯曲过程中存在鲍辛格效应和加工硬化等现象。
- The work hardening rate of pure tantalum was studied by tension test, optical microscope and TEM. 摘要借助力学性能实验、金相显微镜和透射电镜等手段研究了纯钽的加工硬化速率。
- All dies containing coining stations shall have a minimum.750"hardened plate under each station for support. 在有压印工步的地方;至少有一块.;750”厚的热处理板支撑。
- The failure forms of cold work roll including contact fatigue crack, spalling, inclusion crack and wear are discussed. 讨论了冷轧工作辊接触疲劳裂纹、剥落、夹杂物裂纹和磨损等失效形式。
