您要查找的是不是：
- Aiming at the injection mold structures of female mold on stationary mold,the force on the famale mold and male mold are analysed,and the cavity wall thickness are calculated. 针对凹模安装在定模上、凸模安装在动模上的注塑模结构,对矩形型腔模具进行了受力分析和型腔壁厚计算。
- Cavity wall thickness 型腔壁厚
- Range Min and Max.-OD with wall thickness. 范围分钟和最大Od以壁厚度。
- Mor phological features of cancerous cavity had significant relationship with types and grading of pulmonary neoplasm, such as irregular inner bor der ofcavity, thickness of cavity wall and the position of cavity in mass. 空洞内缘不规则似癌梁样改变，空洞壁厚度与空洞在肿瘤中位置特别是肿瘤越小，形成的空洞越小； 肿瘤越大，空洞偏大，且肿瘤又呈分叶样改变等与肿瘤类型与分化程度有明显关系。
- Its filling is surface eluvium material and cavity wall collapsed material. 地下水主要沿着岩层中的裂缝向下渗流，以垂向岩溶为主，主要为高角度的溶蚀裂缝、溶蚀缝合线缝、近于垂直的串珠状中小型溶蚀孔洞沿溶缝、缝合线分布，多为方解石、泥、和其它不同来源成因的渗流砂混合充填。
- The backing of bearings with greater wall thickness is not copper-plated. 轴承壁较厚的轴承,其背衬不镀铜。
- APACO processes Hardboard, MDF or Chipboard up to a wall thickness of 18mm. 橱柜/壁柜/橱柜门板/人造石厨房台面加工制作.
- CPMs presented as bubble (n=41), irregular (n=33), cystic (n=26) or small circular (n=31) cavities, with even (n=61) or uneven (n=70) thickness of the cavity wall. 共有泡样空洞 41枚 ,不规则空洞 3 3枚 ,囊样空洞 2 6枚 ,小环形空洞 3 1枚。 壁厚度均匀者 61枚 ,不均匀者 70枚。
- The forecasted wall thickness was conformed to the experimental result. 预测的壁厚和实验结果吻合得很好。
- Cavity Wall A wall built of solid masonry units arranged to provide air space within the wall. 用实心砌体砌成的墙,墙内放入空气。
- Insulate your home. Cavity wall insulation can cut heat loss through the wall by up to 60 percent. 房屋隔热可以利用空心墙来减少热能损耗,降幅高达60%25。
- SEM showed that the bonding resin can adhere tightly to the cavity wall and amalgam. 对照组合金与洞壁间可见明显间隙。
- End connection including wall thickness of connecting pipe if weld end and any special flange facings or finishes. 连接方式,如果是焊接端口和任何法兰面或表面,则包括连接管道的壁厚。
- What is the foundry's checking frequency for control of core shift and wall thickness? 工厂检验芯偏移以及壁厚的频率?
- Just like the cavity walls of the hypocaust heating in the roman thermae. 我的设计检验了人体和他的即时环境的关系。
- The tube deformation characteristics on ASSEL mill are deformation concentrating at shoulder and wall thickness in rolling zone increasing. ASSEL轧管机具有台肩集中变形、碾轧段壁厚增厚等特点。
- Measure the spcues width between the restoration and the cavity wall by scaming electroscope,and abserve the interfacid form of them. 用扫描电镜测量充填体与窝洞壁间微缝隙间的宽度,并观察充填体-牙体界面的形态。
- The wall thickness of a 1-litre bottle preform is 3mm. The cooling time is 10.8s. 1公升的矿泉水瓶瓶坯壁厚3mm，冷却时间便占10.;8秒。
- Intracerebral haematoma can be evacuated under direct vision endoscopically,without damage to the haematoma cavity wall. 直视下迅速清除脑内血肿，能止血。内窥镜手术是神经外科的一种微侵袭性新技术。...
- The wall thickness of a 5-gallon bottle preform is 8mm. The cooling time is 76.8s. 5加仑瓶瓶坯壁厚8mm，冷却时间是76.;8秒。
