您要查找的是不是:
- Desirable properties for forming include low yield strength and high ductility. 令人满意的成形特性包含了低降伏应力和高延展性。
- Yielding strength is indicative of the stress at which plastic deformation begins. 屈服强度是指塑性形变开始发生时的应力。
- It is revealed that pre-stressing of fibers could effectivelyincrease the elastic limit,yielding strength and fracture strength of VIRALL Iaminates. 结果表明,纤维预拉伸应力能有效地提高VIRALL复合板的弹性极限、屈服强度以及断裂强度。
- The samples of SBS modified HIPS have the maximum work of rupture,elongation in break and higher tensile Yang's modular as well as yielding strength. SBS改性的HIPS试样具有最大的断裂能,最大的断裂伸长率,较高的拉伸杨氏模量、屈服强度,屈服点过后有明显的应变硬化现象。
- Oxygen precipitates (useful for gettering) can reduce the yield strength (critical shear stress) up to fivefole. 氧沉淀(可用作吸杂)会使屈服强度(临界剪应力)降低为五分之一。
- The welder shall be capable of welding (full hard cold-rolled) steel with yield strength of up to 85Kg/mm2. 焊机应能焊(冷轧全硬)其屈服强度大于85Kg/mm2的钢带。
- The V-N microalloy steel with yield strength of 550 MPa is produced by EAF-CSP route. 目前,在EAF-CSP流程中通过V-N微合金化技术可成功生产屈服强度为550 MPa的高强度低合金钢。
- The result show that the yield strength of the bars drop apparently and the tensile strength rise a little. 结果表明,自然时效后钢筋的屈服强度有较大幅度下降,抗拉强度有小幅度的上升。
- The test results showed that the elastic modulus and yielding strength of porose material decreased with increase of its porosity, and the changing trend became slow gradually. 结果表明,多孔材料的弹性模量试验值随其孔隙率的变化在低孔隙率时与理论预测基本吻合;
- The following problems arc discussed in some detail: strong column and fee-ble beam, ratio between axial force and compressive strength, story yielding strength and joint design. 就钢筋混凝土框架抗震设计的强柱弱梁、柱轴压比、楼层屈服强度及节点设计等问题进行了讨论,并提出了相应的改进建议。
- Oxgen precipitates (useful for gettering) can reduce the yield strength (critical shear stress) up to fivefole. 氧沉淀(可用作吸杂)会使屈服强度(临界剪应力)降低为五分之一。
- Change of molecular magnetic moment of motherliquor and shear yield strength are studied in magnetorheological fluid. 对磁流变液中母液分子在磁场作用下磁矩的变化以及由此引起的剪切屈服强度的变化进行了研究.
- Torque values listed are typical or alloy steel bolts (approximately 100,000 psi yield strength) used with carbon or intermediate alloy steel valves. 所列的扭矩值是标准值或适用于合金钢螺栓(屈服强度大约为100,000 psi),配置在碳钢或中间合金钢阀门上。
- Relationship between yield strength and near-neutral pH stress corrosion cracking resistance of pipeline steels-an effect of microstructure. 管道钢的屈服强度和抗近中性pH应力腐蚀开裂间的关系-显微结构的影响。
- Tensile and yield strength are determined by pulling a standardized machined sample in an tensile testing machine until the sample breaks. 抗拉强度和屈服强度的测定是在拉力试验机中将一个加工好的标准试样进行拉伸直至试样断裂。
- The output parameters of the model are three mechanical properties namely ultimate tensile strength (UTS), yield strength (YS) and elongation (ELO). 模型的输出为三个力学性能指标,即抗拉强度、屈服强度和延伸率。
- The results showed that the Vicat softening temperature and the tensile yield strength were improved with the increase of CPVC content. 结果表明,共混材料的维卡软化温度和拉伸屈服强度随CPVC用量的增加而增加;
- We will never yield to invaders. 我们绝不会向侵略者屈服。
- API regulates that the yield strength of flatten specimen from pipe body is used to characterized the yield strength of oil pipeline body. 根据美国石油学会API标准规定,采用管体取样压平试样的屈服强度表征输油管体屈服强度。
- His strength in a crisis is an ace in the hole. 临危不惧是他的看家本领。
- 今日热词
-
- 深远海浮式风电平台 - deep-sea floating wind power platform
-
- 京雄高速公路 - Beijing-Xiongan expressway
-
- 农业及相关产业增加值 - the added value of agriculture and related industries