您要查找的是不是:
- Single speed motor drive connected to a Helical Worm Gear and a totally enclosed Connecting Gear Box with heavy duty chain drive to the rolls and with fixed friction ratio according to customers request (normally 1: 1,2). 系统带有同螺旋涡齿轮以及全封闭齿轮箱的单速马达,它带有重型链传动系统并可根据客户的需要固定摩擦比(通常为1:1.;2)。
- Our company supply: helical gears, bevel gear series, Worm Gear series, gear box series, cycloid-round series, CVT series and various combinations of cut and speed series. 我公司供应:斜齿轮、伞齿轮系列,蜗轮蜗杆系列,齿轮箱系列,摆线针轮系列,无级变速系列及各种组合减、变速系列。
- The spirally threaded shaft of a worm gear. 螺纹蜗轮的刻有螺旋线的柄
- Reducers and worm gear sets can also be made. 减速器及蜗杆副。
- worm gear box 蜗轮蜗杆箱
- The rate of the machine moved up sharply because of changing a big gear box. 由于换了一个大齿轮箱这台机器的速度大大提高了。
- Worm gear drive for continuous adjustment of the pitch. 连续调整节距用蜗轮驱动器。
- Tthe oil quantity of gear box's lubricating oil. 卷扬机齿轮箱润滑油油量是否符合规定。
- Based on customer requirements and various types of research and development worm motor, gear box and various types of motor putter series. 并可以根据客户要求研发各类蜗杆电机,齿轮箱电机及各类推杆系列。
- Intermeshed worm and worm gear provide precise driving without gaps. 蜗杆和涡轮组合传动精确无偏差。
- Alignment inspection installation of shaft generator and gear box. 轴带发电机及齿轮箱安装检查。
- Two layouts of gear box in twin screw extruders are discussed. 文中介绍了双螺杆挤出机齿轮传动的两种设计方案。
- The cycloidal equidistant-curve worm gearset is the new type of worm and worm gear transmission equipment. 摆线等距曲线蜗轩是一种新型的蜗杆传动。
- The bottom end of the shaft has a worm gear that rotates as the wheel is turned. 转向轴的底端有一个蜗轮传动装置,当蜗轮传动装置转动时,带动车轮转动。
- A gear sector is meshed with the worm gear; rotation of the worm gear causes the gear sector to rotate. 蜗杆齿带动齿扇转动,齿扇与蜗杆齿啮合,这使的与齿扇相连接的转向摇臂左右摆动。
- This is the reference for the CAD development of the vehicle gear box. 供车辆变速箱cad软件开发时参考。
- The antiwear was enhanced in L-CKE worm gearing oil with DAE. DAE在L CKE涡轮蜗杆油中使耐磨性增强 ;
- Screws protected by a torque limiter mounted in between motor and gear box. 螺杆由安装在马达和齿轮箱之间的扭矩限制器保护。
- Check for scores, nicks or burrs on the rack piston finished surfacSlight wear is normal on the worm gear surfaces. 检查齿条活塞抛光表面是否有刮痕、刻痕或磨擦。涡轮表面的轻微磨损是正常的。
- Special worm gear hobs with circular tooth, double pitch and involute etc, can also be ordered. 圆弧齿、双螺距、渐开线等特殊蜗轮滚刀也可以订货。