您要查找的是不是：
- wheel truing brake shoe 车轮踏面修整闸瓦
- truing brake shoe 整形闸瓦
- Check rear brake shoe adjustment with standard brake gauge. 用标准刹车仪表检查后刹车蹄片调整。
- Friction is applied to the inside of a spinning drum by the brake shoe. 通过闸皮摩擦力作用到内部的纺纱鼓上。
- Wheel truing cycles on the Metro have been extended from 50,000 km to somewhere between 200,000 km and 250,000 km. 地铁公司的车轮打磨维修周期已从50，000公里延长到200，000-250，000公里。
- Wheel truing cycles on the Metro have been extended from50,000 km to somewhere between200,000 km and250,000 km. 地铁公司的车轮打磨维修周期已从50，000公里延长到200，000-250，000公里。
- This picture shows the spokes after fine tuned, so called ‘ wheel truing’.This stage takes me several hours, needs patience and delicate adjustment. 此图为钢丝已经精密调整;即所谓的把轮子调整到正圆.;这个阶段花了我数小时;需要耐性精致微调
- Reinstall brake drums and wheel/tire assemblies after brake shoe adjustment is complete. 刹车蹄片调整完成后，重新安装刹车鼓和车轮/轮胎组合。
- The accident was caused by worn brake shoes. 这事故是因煞车过度磨损而造成的。
- A spring attached to each brake shoe returns it also to its original position, free of the brake drum. 附接在各个制动蹄上的弹簧也将制动蹄拉回原位，不与鼓轮接触。
- Multi-body system theory was employed to establish the geometric error model of grinding wheel truing, which was for forming the slewing ring s ball track. 摘要应用多体运动学原理，建立了回转支承滚道成形磨削的砂轮修形几何误差模型；
- This paper presents a new kind of design principle and a structure scheme of brake shoe adjuster autotestor. 该文给出了一种全新的闸调器试验台的设计原理、结构方案。
- Mid-Manganese alloy cast iron brake shoe was studied and compared with mid-phosphorous and high-phosphorous cast iron. 本文以中锰合金铸铁闸瓦为研究对象,并与中磷铸铁、高磷铸铁进行了对比研究。
- Install rotor, caliper, and wheel and tire assembly, then adjust parking brake shoes. 安装转子，夹制器，和车轮和轮胎组合，然后调节手煞车蹄片。
- Whichever method is used, and finally the need to brake drum brake shoe and the contact area for more than 70%. 无论采用哪种方法，最后必须使制动鼓与制动蹄的接触面积达到70%25以上。
- The grinding wheel truing error caused by the grinding machine geometric error can lead to the change of the angle contacting and the opening size of the slewing ring s ball track. 由机床非线性几何误差引起的砂轮修形误差会导致磨削的回转支承滚道开口变大和接触角变小；
- After the circuit is well connected, you pull down the brake shoe and then the electric lamp will be turned on. 电路连接好后，把闸刀放下来电灯就能亮了。
- This paper introduces the shape grinding process of the decides grid trough and the rule's contour and the process of grinding wheel truing,analyzes the process simulation by computer. 本文主要介绍了容栅式数显焊接棱角度错边量检测仪尺身定栅槽、基尺外形的成型磨削加工工艺以及砂轮修整工艺,此外,对成型磨削过程中的计算机模拟进行了分析。
- Structurally, an automotive brake system contains these major parts like brake drum, brake shoe, brake lining, etc. 在结构上，汽车刹车系统包括的主要零件包括制动鼓、制动块、制动衬片等。
- For the diamond wheel truing and dressing, especially for high precision arc diamond wheel, the GC cup truing technology is often adopted to obtain fine grinding performance and truing efficiency. 摘要对于金刚石砂轮修整，尤其是有高精度要求的圆弧金刚石砂轮，杯形砂轮修整技术可以获得较好的砂轮磨削性能以及修整效率。
