您要查找的是不是:
- The inner quality of welding line,the welding structure,the mechanical property,the welding efficiency and the line energy of the two types of welding methods are contrastively studied. 分析焊缝内部的质量、焊接接头的组织、焊接接头的强度,对比两种工艺的焊接效率和线能量,研究结果表明:在焊缝内部质量、焊接强度方面,双丝焊优于单丝焊;
- welding line energy 焊接线能量
- weld line energy 焊接线能量
- THE EQUIPMENTS AND FIXTURE OF WELDING LINE. 焊装线设备及工装夹具
- Introduced planar welding line detect sensor based on GMR. 简述了基于GMR的二维焊缝检测传感器。
- A three-dimensional welding line detect sensor based on GMR was introduced. 简述了基于GMR的三维焊缝检测传感器。
- Weld Area Crack. A crack in or immediately adjacent to the weld line. 焊缝区裂纹。在焊缝线或紧靠焊缝线出现的裂纹。
- Cords and straight line energy cut up the rotational energy flow one ascends into the further that one master's the initiations in ascension. 绳索和直线能量切碎你开始提升并深入提升时进入的旋转能量流。
- With Cold Jet, complete weld lines can be cleaned in 25 minutes. 如果使用Cold Jet,彻底清洁焊缝可在25分钟之内完成。
- Under the constant bending times, the biggest bending angle can be obtained with an optimal accumulative line energy value. 在扫描次数一定的情况下,存在一个最优的累积线能量使弯曲角达到最大;
- Do not make a round trip jolty porch rail, lest the welding line of baluster bottom ruptures. 不要往返摇动阳台栏杆,以免栏杆底部的焊缝断裂。
- Variations in the properties of the weld occurring at short regular intervals along the weld line due to repetitive variation in welding heat. 由于焊接热量周期变化,使得沿焊缝线每一固定的小间距焊缝的性能出现周期性变化。
- Straight lined energy flow or sacred geometry will only ascend one so far. 直边的能量流或神圣几何学只能提升一个人到这么远。
- Utilized this method to segmentalize the image of oil derrick arc welding robot welding line gets up the good effect. 将该方法运用于石油井架弧焊机器人焊缝图象的识别中起到很好的效果。
- The maximum value of gapwise-averaged birefringence along the weld line occurred at a small distance from the obstacle. 制品最大双折射值出现在嵌件后一定距离处。
- Study on the properties of welding line near line section aluminium lithium alloy 1420 by Russia scholar is introduced. 主要介绍了俄罗斯学者关于铝锂合金1420焊缝近缝区性能的研究点滴。
- In the experiments of this research, GTAW butts thin plates of stainless steel and forms a weld line. 摘要本研究以不锈钢薄板在惰性气体钨棒电弧焊对接焊方式进行研究。
- Pinhole. A short unwelded area in the weld line extending through the entire pipe so that fluid will leak out through the area very slowly. 针孔。指焊缝线上位焊接的、贯穿管子整个壁厚的细孔,可导致流体从该孔缓慢漏出。
- By changing the structure of welding line and assessing minutia, the fatigue intension of framework welding line will be increased. 通过改变焊缝结构,使焊缝的评定细节发生变化,从而提高机架焊缝的疲劳强度。
- All these can be well used for reference to study the cause of molding defects (e. g. warpage, weld line) of ultra-thin wall plastic parts thoroughly. 该结论为深入开展超薄塑件成型缺陷(如翘曲、熔接痕)的形成机理研究提供了有益的借鉴。