您要查找的是不是：
- welding between pipe connect 管口和筒体间焊缝
- The pipe connects with the sewer . 这根管子连接下水道。
- Be suitable for spot welding between electric wheels motor plane commutator and wire head. 适用电动车轮鼓电机平面换向器与导线线头的点焊。
- This pipe connects with a smaller one. 这管子和一个较小的管子连通着。
- Be suitable for spot welding between electromotor commutator with hooks and slots and rotor wire. 适用带钩、开槽电机换向器与转子导线的点焊。
- The pipe connects with the sewer. 这根管子连接下水道。
- Be suitable for spot welding between rotor wire head and electromotor commutator with hooks and slots. 适用带钩,开槽电机换向器与转子导线线头的点焊。
- External air duct and exhaust pipe connector. 外置式出入油管连接座。
- Unscrew the oil pipe connection. 拧开油管接头。
- Be suitable for spot welding between rotor wire head and electromotor commutator with hooks and slots and plane commutator. 适用带钩,开槽电机径向、平面换向器与转子导线线头的点焊。
- Antiwear (AW) Agent Additive that is active in preventing damage caused by occurrence of solid phase welding between sling surfaces without local surface melting. 抗磨（aw）添加剂相互滑动的表面因发生相互摩擦会造成损坏。抗磨添加剂就是能有效防止这类磨损，同时又不会发生滑动的表面熔化的添加剂.
- Antiwear(AW)Agent Additive that is active in preventing damage caused by occurrence of solid phase welding between sliding surfaces without local surface melting. 抗磨(aw)添加剂相互滑动的表面因发生相互摩擦会造成损坏。抗磨添加剂就是能有效防止这类磨损，同时又不会令发生滑动的表面熔化的添加剂。
- Objective:To discuss the nursing experience on the new CAPD pipe connect system and responsibility system nursing in treating chronic renal failure (CPF). 目的探讨新的腹膜透析管连接系统(双联系统)及责任制护理在治疗慢性肾功能衰竭中的护理体会。
- Though to improve the manufacturing processes of the modules welding between spire-wing tube and header for the conhired cucle HRSG reduce the difficulty of the assembling. 通过对联合循环余热锅炉螺旋翅片管与集箱焊接的组件的制造工艺进行改进,降低了装配难度。
- Check whether or not the fuel supplying pipe connector is loosing. 检查供油管路接头是否松动。
- It used to be made as pipe connecter、engineering springs etc. 目前，SMA主要用作工程材料，如管接头、工程弹簧等。
- This paper introduces the design and operations of expanded joint between pipe and plate in column pipe heat exchanger,the quality inspection a nd the problems which should be atten tive. 介绍了列管式热交换器中管子和管板的胀接设计、操作以及质量检查过程中应注意的问题及解决办法。
- It is deemed that the dissimilar steel welding between the locating piece and reheater tubes and unproper structure of the location piece are the major reason that causes the tube leakage. 分析了再热器管频繁泄漏的原因,认为定位块与再热器管的异种钢焊接及定位块结构的不合理是导致泄漏的主要原因,同时提出了改造方案。
- I've seen some pieces like this(both official Dao and civilian Dao).Maybe the welding between soleplate of head and foreside has fallen.Maybe in the year from Yuan dynasty to early Qing dynasty. 也见过几例这样装的(官刀民造都有);可能是刀首底板与前部开焊丢失;老配的.;典型制式刀;元至清早都有可能
- An external overflow pipe connects the absorber reaction tank to the box. 外部溢流管把吸收塔反应箱和密封箱连接起来。
