您要查找的是不是：
- During the MPF of the TWB,the weld lines move and their movements increase as the distance between the initial weld line location and th... 成形过程中,焊缝初始位置距离板料中心越远、板料厚度相差越大、板料变形量越大,焊缝偏移量就越大。
- weld line location 熔接痕位置
- Weld Area Crack. A crack in or immediately adjacent to the weld line. 焊缝区裂纹。在焊缝线或紧靠焊缝线出现的裂纹。
- Where is the start line located? 起航线在哪里?
- THE EQUIPMENTS AND FIXTURE OF WELDING LINE. 焊装线设备及工装夹具
- The maximum value of gapwise-averaged birefringence along the weld line occurred at a small distance from the obstacle. 制品最大双折射值出现在嵌件后一定距离处。
- With Cold Jet, complete weld lines can be cleaned in 25 minutes. 如果使用Cold Jet,彻底清洁焊缝可在25分钟之内完成。
- In the experiments of this research, GTAW butts thin plates of stainless steel and forms a weld line. 摘要本研究以不锈钢薄板在惰性气体钨棒电弧焊对接焊方式进行研究。
- Pinhole. A short unwelded area in the weld line extending through the entire pipe so that fluid will leak out through the area very slowly. 针孔。指焊缝线上位焊接的、贯穿管子整个壁厚的细孔，可导致流体从该孔缓慢漏出。
- All these can be well used for reference to study the cause of molding defects (e. g. warpage, weld line) of ultra-thin wall plastic parts thoroughly. 该结论为深入开展超薄塑件成型缺陷（如翘曲、熔接痕）的形成机理研究提供了有益的借鉴。
- The results show that the method can effectively resolve the TWB forming process parameters, and that the weld line movement can be reduced by more than 75%. 优化计算结果表明，该方法能有效求解拼焊板成形过程参数，使焊缝有害偏移量减少75%25以上。
- Introduced planar welding line detect sensor based on GMR. 简述了基于GMR的二维焊缝检测传感器。
- The line location for orifice runs, venturi tubes and flow nozzles shall allow sufficient access and space for installation of differential pressure instruments and instrument piping. 孔板导压管、文丘里管和流量管嘴的管线位置，应使差压仪表和仪表导压管具有足够的通道和安装空间。
- They also look for potential molding defects, such as gas entrapment, weld lines, shorts and sinks. 也可以看出潜在的模塑缺陷如气体夹陷、熔接线、缺胶和凹陷等。
- To date, it is not fully used, because it is very difficult to detect clear and steady image owing to the noise interferences that exist in the nearby weld line caused by vast arc, spatter, etc. 但是目前还未能有效加以利用,这是因为熔池区存在大量的弧光、飞溅等噪声的干扰,不易获得清晰稳定的近熔池区图像。
- A three-dimensional welding line detect sensor based on GMR was introduced. 简述了基于GMR的三维焊缝检测传感器。
- This article introduces the technological method of using glass fibre tubes to solve the splitting problem from the weld line after the forming of the thermosetting product "pedestal". 利用玻璃纤维套管,解决了热固性塑料制件“底座”成型后从熔接线处开裂的问题。
- A Shortcut Method of Center Line Location of Road 道路中线测设的一种快捷方法
- Weld lines can take more than two hours to clean completely by using the traditional methods of hand scraping and chemical use. 使用传统手工刮削法与化学品彻底清洁焊接纹需要两个小时以上的时间。
- As major facilities of the hotrolled pipe production line located in the pipe rolling division of Tianjin Steel Tube Corp. 脱管机和定径机是天津钢管公司轧管厂热轧管生产线上的主要设备。
