您要查找的是不是:
- EXPLORING ON EFFECT OF FORMING PRESSURE ON BULK DENSITY, WATER ADSORPTION RATE AND APPARENT POROSITY OF MATRIX 成型压力对基体体积密度、吸水率和显气孔率影响的探讨
- water adsorption rate 吸水率
- The Porous high strength granular solid Zeolite is treated properly,it can be used to treat Ni containing waste water with a Ni adsorption rate up to 91. 5%. 多孔高强度沸石颗粒,经适当处理后,将其用来处理含镍废水,对镍的吸附效率可达91.;5%25。
- The remaining quantity of Cadmium as in water, the adsorption rate of Cadmium and the Cadmium quantity adsorbed by a unit of specimen weight were recorded separately. 得到了相应条件下的镉离子残留量、吸附镉离子质量分数、单位试样吸附镉的质量。
- The remaining quantity of lead in water, the adsorption rate of lead and the lead quantity adsorbed by a unit of specimen weight are recorded separately. 得到了相应条件下的铅离子残留量、吸附铅离子质量分数、单位试样吸附铅的质量。
- The tile water adsorption also affect on the adhesive strength clearly. 瓷砖的吸水率对粘结强度也有明显的影响。
- The remained concentration of Tin cations in water, the adsorption rate of Tin cations and the adsorbed amount by a unit of specimen weight are separately detected. 得到了相应条件下的锡离子残留量、吸附锡离子百分数、单位试样吸附锡的重量。
- The adsorption rate of BSA on TiO_2 surface was lower than that on HAP surface. 结果表明,BSA在2种电极表面的吸附过程均分为吸附和重排2个过程,BSA在TiO_2上吸附速度慢于在HAP上的吸附,且难达到稳定状态。
- Protects against loss of dispersibility in warehouse by hindering water adsorption from air. 防止颜料在储存时从空气中吸潮,从而保持颜料分散性。
- Water adsorption isotherms of ACF were type V with broad hysteresis loop at middle relat... ACF表面的初始吸附点多,则在低、中压时的水吸附量就大。
- With increasing CaCO3 contents, vicar softening temperature and hardness of the blend increases, while the water adsorption decreases. 同时活性CaCO_3的加入使ABS/PVC/PE-C共混体系的吸水率有所降低,维卡软化温度和硬度则随着CaCO_3含量的增加而有所升高。
- The adsorption rate of NKA-9 to Bilirubin in hematoplasma is close to 95% under better conditions. 在较佳吸附条件下NKA-9树脂对血浆中胆红素的最大吸附率接近95%25。
- Sintering at high temperature may enhance densification and decrease the moisture adsorption rate. 同时,由于试体之致密化,其吸水率则随烧结温度增加而降低。
- The resultants were characterized by IR, DSC.The tensile strength and water adsorption of the product membrane increased. 对该聚电解质用IR、DSC表徵,并检则其拉伸性能和吸水率,效果很好。
- The resultants were characterized by IR, DSC.The tensile strength and water adsorption of the product membrane increase... 对该聚电解质用IR、DSC表征,并检测其拉伸性能和吸水率,效果很好。
- The resin showed good adsorption affinity for Cr3+ with low concentration. The adsorption rate was high in the earlier stage but low after 40min. 结果表明,树脂对低浓度Cr3+的吸附效果好,前期吸附速度快,40min后吸附速率趋缓;
- When the adsorption time was 40 min, 20g sorbet was used for 1 liter solution containing with 50mg/L fluoride, the adsorption rate was up to 74. 6% . 室温条件下;F-离子初始质量浓度50mg/L;吸附剂投加量20g/L;吸附振荡时间为40min时;无机柱撑蒙脱石对F-的去除率达74.;6%25;较相同条件下未改性柱撑蒙脱石对F-离子的去除率提高了19
- Its density, water adsorption, coefficient of heat conducting and the coefficient of steam pervasion are all lower than those of other board heat preservasion materials. 其密度、吸水率、导热系数及蒸汽透系数等方面均低于其它类型的板状保温材料。
- Experimental results showed, that adsorption rate and“quasi equilibrium”adsorption amount depend on the concentration of solution and velocity. 实验结果表明,吸附速率、“准平衡”吸附量等均与溶液浓度、流动速度有关。
- Conclusion: Molecularly imprinted polymers can adsorb propofol in human plasma, and the adsorption rate is influenced by the concentration of substrate. 结论:分子印迹聚合物可以从人血桨中吸附异丙酚,其吸附率受底物浓度的影响。